Zhongshan Grand Enterprise Co. Ltd FCGRAND User Manual
3
Plug in Wall Receiver Units.
Plug the individual Wall Receiver Unit (s) into any standard 3-prong AC indoor wall outlet.
Plug the individual Wall Receiver Unit (s) into any standard 3-prong AC indoor wall outlet.
Operation and Safety.
Use only 1 Super Switch Wall Receiver Unit per AC outlet. A distance of 24 inches should be maintained between individual Wall
Receiver Units. Do not overload individual Super Switch Wall Receiver unit beyond 1000 watts. Maximum output load:
125V/60Hz/10A. FOR INDOOR USE ONLY. DO NOT use Super Switch to control TV ON/OFF Power. Super Switch is not
recommended for use with computers and computer monitors. Super Switch is not a circuit overload protector and is not
designed or warranted for this purpose. To adequately protect your valuable home electronics, use a commercially available and
rated circuit overload protector.
Wall Receiver Unit Function.
ON/OFF Button (s). The power control button on the front of the wall receiver unit is used to manually power the wall receiver
ON when pressed and OFF when pressed again. The unit can also be powered ON with the Hand-Held remote control. The Red
LED ON light on the front of the wall receiver unit will illuminate when power is ON. If the Red LED (ON) does not illuminate
check to be sure your indoor wall outlet is powered ON (check household circuit breakers, GFI Circuits).
Remote Control Functions.
The Hand-Held Remote Control unit has a single Red LED indicator light that shows the radio signal has been sent. The Hand-
Held Remote Control features three buttons marked 1, 2, and 3 respectively. Each button 1, 2, 3; corresponds to a specific wall
receiver unit. Each of the individual receivers is clearly labeled 1, 2 or 3 to correspond to the buttons on the Hand-Held Remote
Control unit. Pressing the buttons on the Hand-Held Remote Control turns the power ON or OFF at the corresponding Wall
Receiver Unit.
NOTE:
Do not overload individual Super Switch Wall Receiver unit beyond 1000 watts. Before plugging any appliance into the Super
Switch Wall Receiver, review the appliances wattage. If it exceeds 1000 watts, it should not be used with the Super Switch.
Maximum output load: 125V/60Hz/10A.
Use only 1 Super Switch Wall Receiver Unit per AC outlet. A distance of 24 inches should be maintained between individual Wall
Receiver Units. Do not overload individual Super Switch Wall Receiver unit beyond 1000 watts. Maximum output load:
125V/60Hz/10A. FOR INDOOR USE ONLY. DO NOT use Super Switch to control TV ON/OFF Power. Super Switch is not
recommended for use with computers and computer monitors. Super Switch is not a circuit overload protector and is not
designed or warranted for this purpose. To adequately protect your valuable home electronics, use a commercially available and
rated circuit overload protector.
Wall Receiver Unit Function.
ON/OFF Button (s). The power control button on the front of the wall receiver unit is used to manually power the wall receiver
ON when pressed and OFF when pressed again. The unit can also be powered ON with the Hand-Held remote control. The Red
LED ON light on the front of the wall receiver unit will illuminate when power is ON. If the Red LED (ON) does not illuminate
check to be sure your indoor wall outlet is powered ON (check household circuit breakers, GFI Circuits).
Remote Control Functions.
The Hand-Held Remote Control unit has a single Red LED indicator light that shows the radio signal has been sent. The Hand-
Held Remote Control features three buttons marked 1, 2, and 3 respectively. Each button 1, 2, 3; corresponds to a specific wall
receiver unit. Each of the individual receivers is clearly labeled 1, 2 or 3 to correspond to the buttons on the Hand-Held Remote
Control unit. Pressing the buttons on the Hand-Held Remote Control turns the power ON or OFF at the corresponding Wall
Receiver Unit.
NOTE:
Do not overload individual Super Switch Wall Receiver unit beyond 1000 watts. Before plugging any appliance into the Super
Switch Wall Receiver, review the appliances wattage. If it exceeds 1000 watts, it should not be used with the Super Switch.
Maximum output load: 125V/60Hz/10A.
Learning Function
The Super Switch has the ability to be programmed to control multiple Wall Receiver Units with a single button on a remote control.
For example, if you wish to turn all three Wall Receiver Units ON and OFF from button number one on the remote control, do the
following:
For example, if you wish to turn all three Wall Receiver Units ON and OFF from button number one on the remote control, do the
following:
Follow these easy steps:
1. Plug Wall Receiver Units into Indoor AC wall outlets.
2.
Press and hold the manual POWER ON/OFF button on the first Wall Receiver Unit you wish to “learn” for 5 seconds.
3. Release the button on the Wall Receiver Unit when the red POWER indicator LED on the Wall Receiver Unit begins
blinking.
4. Again, press and hold the manual POWER ON/OFF button on the first Wall Receiver Unit for 5 seconds until the red
POWER indicator LED on the Wall Receiver Unit begins blinking.
5. Point the Hand-Held remote control at the Wall Receiver Unit on the wall and
press the button on the Hand Held Remote
Control (1, 2, or 3) that you want to correspond to the Wall Receiver Unit (s). The red POWER indicator LED on the
Hand Held Remote Control flashes once when it has learned the button position that corresponds to the Wall Receiver
Unit.
Hand Held Remote Control flashes once when it has learned the button position that corresponds to the Wall Receiver
Unit.
6. Press the manual POWER ON/OFF button on the Wall Receiver Unit one time or wait for 8 seconds to finish the
programming process.
7. Repeat this process for each Wall Receiver Unit that you want to be controlled from the same Hand Held Remote control
button.