Duravit AG 596000098001 User Manual
7
Disconnection device having a contact separation in all poles that provide full disconnection under
overvoltage category III conditions must be incorporated in the fixed wiring in accordance with the
wiring rules.The nominal cross-sectional area of the conductors should be AWG16(1.5mm
overvoltage category III conditions must be incorporated in the fixed wiring in accordance with the
wiring rules.The nominal cross-sectional area of the conductors should be AWG16(1.5mm
2
), and the
spec of wire shall be at least H05VV-F or above. The length of the power cord should be 19 5/8” (50
cm) for the convenience of installation.
cm) for the convenience of installation.
Power supply cord need to be prepared at the customer end.
Electric wiring has to be done in accordance with all local codes, or in the absence of local codes,
with the National Electrical Codes.
with the National Electrical Codes.
3.3 Safety instructions
Read and observe the following safety instructions carefully!
Requirements for the user
For the disabled: this product is not intended for use by persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge unless they have been given supervision or instructions
concerning the use of the product by a person responsible for their safety.
For children: children should be supervised to ensure that they do not play with the product. This product
can be used by children aged from 8 years and above.
capabilities or lack of experience and knowledge unless they have been given supervision or instructions
concerning the use of the product by a person responsible for their safety.
For children: children should be supervised to ensure that they do not play with the product. This product
can be used by children aged from 8 years and above.
Health damage
Do not use the product while bathing.
If the product is standing in the water, please cut off the power supply immediately.
The product must be grounded.
Do not insert a finger into or keep hands near the air dryer outlet.
Only use tap water or potable well water (underground water). Do not use seawater.
When the product is in use again after a long period of time of not using, please re-circulate the water first
using wand self-cleaning, otherwise stagnant water may cause skin irritation.
If the product is standing in the water, please cut off the power supply immediately.
The product must be grounded.
Do not insert a finger into or keep hands near the air dryer outlet.
Only use tap water or potable well water (underground water). Do not use seawater.
When the product is in use again after a long period of time of not using, please re-circulate the water first
using wand self-cleaning, otherwise stagnant water may cause skin irritation.
Only use the device when it is fully functional
• Make sure that the power cable is not damaged.
• The power cable must not become jammed or pinched.
• Keep the power cable away from hot surfaces and sharp edges.
• Never touch the power cable with wet hands.
• Do not use the product if it is not working properly. Disconnect it from the mains immediately. Close
the water cut-off valve to interrupt the water supply. Contact your installer.
• Make sure that the power cable is not damaged.
• The power cable must not become jammed or pinched.
• Keep the power cable away from hot surfaces and sharp edges.
• Never touch the power cable with wet hands.
• Do not use the product if it is not working properly. Disconnect it from the mains immediately. Close
the water cut-off valve to interrupt the water supply. Contact your installer.
Avoid malfunctions and damage to the product as a result of improper use.
• Do not install the SensoWash® in a room exposed to excessive moisture. Please ensure sufficient
ventilation and no condensation shall be formed on the product.
• Do not install or use the SensoWash® in rooms where there is a danger of frost or water may freeze.
The room temperature must not be less than 4
• Do not install the SensoWash® in a room exposed to excessive moisture. Please ensure sufficient
ventilation and no condensation shall be formed on the product.
• Do not install or use the SensoWash® in rooms where there is a danger of frost or water may freeze.
The room temperature must not be less than 4
°C. Freezing water may cause product damage.