Marmitek Control Anywhere 09665 User Manual
Product codes
09665
10
MARMITEK
SAT, etc.) on the rubber keypad. Note The Brand Search Method is not available for
CD/Audio appliance.
CD/Audio appliance.
7. Display will show the Code Setup Screen. Using the table, press and release the
numerical key (0-6) corresponding to desired Manufacturer. Note - pressing "0"
carries out a full library search same as normal Code Search Method.
carries out a full library search same as normal Code Search Method.
Brand CODE
Philips/Radiola/Aristona/Erres 1
Sony/Panasonic/JVC/Sharp Akai/Toshiba/Daewoo
Sony/Panasonic/JVC/Sharp Akai/Toshiba/Daewoo
2
Thomson/Brandt
3
Telefunken/Saba/Nordmende
4
Grundig/Blaupunkt
5
Nokia/ ITT
6
8. Press and release the Touchscreen "SEARCH" Key.
9. Display will show the Search Setup Screen. Press the Touchscreen "UP" key (or Power
or Play) repeatedly until the Device to be controlled changes channel. Alternatively,
you can use the Channel Up & Down keys. Press and release the Touchscreen "OK"
(or Mute) key to install the Code. Display will return to the Main Setup Screen.
If you accidentally overshoot the Code required, press the Touchscreen "DOWN" or
Channel Down to backtrack through the Library to return to the correct code.
Pressing the Touchscreen "UP" key (or Power or Play) will change direction to forward
again.
you can use the Channel Up & Down keys. Press and release the Touchscreen "OK"
(or Mute) key to install the Code. Display will return to the Main Setup Screen.
If you accidentally overshoot the Code required, press the Touchscreen "DOWN" or
Channel Down to backtrack through the Library to return to the correct code.
Pressing the Touchscreen "UP" key (or Power or Play) will change direction to forward
again.
10. Repeat this procedure for any other appliance you want to control.
ATTENTION: the Brand Search method does not work for CD and AUDIO.
11. The Brand Search Method entry is now complete. Press and release the Touchscreen
"EXIT" key to return to normal operation.
Notes:
a. When all codes under a Brand have been searched the LED will "error" flash
a. When all codes under a Brand have been searched the LED will "error" flash
indicating end of the search and Main Setup Screen will be displayed.
b. The above search procedure assumes that you want to store VCR codes under the
VCR key, Cable codes under CBL, etc. If you want, for example, to store a VCR code
under CBL, etc., then the Mode key must be "primed" for the new appliance. First
follow the "Programming using 3 Digit Code Table" procedure and then enter any
VCR code prior to carrying out the above search steps.
under CBL, etc., then the Mode key must be "primed" for the new appliance. First
follow the "Programming using 3 Digit Code Table" procedure and then enter any
VCR code prior to carrying out the above search steps.
Method B: Programming using the 3 Digit Code Tables
Note: you can dedicate any appliance (TV, DVD, SAT...) to the VCR, DVD, SAT, CD, AUDIO,
CBL and Marmitek X-10 Home Control keys: you need first to enter the 3 digit code
of the appliance you wish to control (found in the code book). In any case, follow the
method below:
Note: you can dedicate any appliance (TV, DVD, SAT...) to the VCR, DVD, SAT, CD, AUDIO,
CBL and Marmitek X-10 Home Control keys: you need first to enter the 3 digit code
of the appliance you wish to control (found in the code book). In any case, follow the
method below:
1. Make sure your appliance is switched on (for example TV)
2. Activate your ET35 remote by touching the screen
3. Press and hold the Setup key until the LED remains on (this occurs after approximately
2-3 seconds) and display shows the Main Setup Screen.
20055_20061108_UG_EasyTouch_35_touchscreen_remote 09-11-2006 10:22 Pagina 10