Havis PKG-PSM-203 User Manual

SPACER

OFFSET MOUNT 

BASE

SEAT BOLT

SUPPLIED

WITH

HARDWARE KIT

PLACE THE SPACER AT  THE                     

1.

SEATBOLT LOCATIONS TO FILL THE  

GAP BETWEEN THE SEAT BRACKET      

AND BASE. 

ALIGN BASE MOUNTING HOLES TO 

2.

SEATBOLT MOUNTING POINTS. 

USING  SUPPLIED SEATBOLTS, 

INSERT BOLTS PASSING THROUGH 

THE SPACER AND SEAT BRACKET 

THEN HAND TIGHTEN TO AVOID 

STRIPPING THE THREADS.

FULLY TIGHTEN SEAT BOLTS.   

3.

BASE

FILLER

FILLER

SUPPLIED

WITH

HARDWARE KIT

REMOVE REAR SEATBOLTS. TILT THE SEAT 

1.

FORWARD WHILE PULLING THE SEAT 

TOWARDS THE REAR TO DISENGAGE 

THE FRONT SEAT HOOKS.

ALIGN MOUNTING BASE CUT-OUT TO 

2.

FRONT SEAT HOOK ENTRY. RETURN THE 

SEAT TO ITS ORIGINAL LOCATION 

WHILE HAVING THE BASE SANDWICHED 

BETWEEN THE SEAT BRACKET AND 

VEHICLE FLOOR. PUSH IN THE 2 FILLERS 

ON EACH SIDE TO FILL THE GAP 

BETWEEN THE SEAT BRACKET AND BASE. 

SECURE THE FILLER USING SUPPLIED 

HARDWARE. NOTE ONLY ONE KEY 

SHAPED FILLER NEEDED ON DRIVERS 

SIDE IF HUMP BRACKET IS BEING USED.

REATTACH REAR SEAT BOLTS AND 

3.

FULLY TIGHTEN.

BASE

SUPPLIED

WITH

HARDWARE KIT

OFFSET MOUNT

LIFT THE SEAT AND PLACE BASE 

1.

BETWEEN SEAT BRACKETS AND 

VEHICLE FLOOR, ALIGN MOUNTING 

HOLES TO SEATBOLT LOCATIONS.  IN 

SOME VEHICLES,  THE SEATBOLTS ARE 

ORIENTATED AT AN ANGLE, IF THIS IS 

THE CASE, THE BASE WILL SIT ON TOP 

OF THE SEAT BRACKET.

USING EXISTING SEATBOLTS, LOOSELY 

2.

ATTACH ALL SEATBOLTS. USE CAUTION 

WHEN THREADING THE BOLTS TO 

AVOID STRIPPING THE THREAD.

FULLY TIGHTEN SEAT BOLTS.

3.

BASE

(C-HDM-401)

INCLUDED IN

C-HDM-106/107 

HARDWARE KIT

STIFFENER

BRACKET

LIFT THE SEAT AND PLACE BASE 

1.

BETWEEN SEAT BRACKETS AND 

VEHICLE FLOOR, ALIGN MOUNTING 

HOLES TO SEAT BOLT MOUNTING 

POINTS. SEE NOTE 3 ABOVE.

USING EXISTING SEATBOLTS, LOOSELY 

2.

ATTACH ALL SEATBOLTS. USE CAUTION 

WHEN THREADING THE BOLTS TO 

AVOID STRIPPING THE THREADS.

ATTACH POLE ASSEMBLY USING 

3.

SUPPLIED HARDWARE.

INSTALL SUPPORT ARM AS SHOWN 

4.

USING HARDWARE SUPPLIED WITH C-

HDM-401 KIT. ENSURE THE C-HDM-401 

DOES NOT CLAMP ABOVE THE 

HORIZONTAL SLOT IN THE POLE.

INSTALL STIFFENER BRACKET AS 

5.

SHOWN, DRILL AND BOLT TO THE SEAT 

IF DESIRED.

FULLY TIGHTEN SEAT BOLTS.

6.

SUPPORT ARM

C-HDM-204, 205, 212, 213, 214, 215, 

1.

216, 217 ARE NOT COMPATIBLE WITH 

THE C-HDM-100 SERIES.

TO ATTACH C-HDM-204, 205, 214, 215 

2.

LINE UP THE MOUNT WITH THE NUTS IN 

THE CONSOLE, ATTACH USING 1/4-20 

BOLTS. HOLES CAN BE DRILLED AND 

THE MOUNT THROUGH BOLTED IF 

NECESSARY.

TO MOUNT C-HDM-212, 213, 216, 217, 

3.

HOLES MUST BE DRILLED AND THE 

MOUNT THROUGH BOLTED USING THE 

HARDWARE PROVIDED.

SEE NOTES FOR DRILLING

4.

1/4-20 x1/2" LG

1/4" SERRATED WASHER

C-HDM-103- see FIG. 4

C-HDM-104- see FIG. 2

C-HDM-105- see FIG. 2

C-HDM-106- see FIG. 3

C-HDM-107- see FIG. 3

C-HDM-109- see FIG. 2

C-HDM-121- see FIG. 2

C-HDM-124- see IND. INSTALL

C-HDM-131- see IND. INSTALL

C-HDM-133- see IND. INSTALL

C-HDM-134- see IND. INSTALL

C-HDM-135- see IND. INSTALL

INSPECT PARTS RECEIVED TO MAKE SURE YOU HAVE THE RIGHT BRACKETS FOR THE SPECIFIC VEHICLE.

1.

REMOVE ALL PLASTIC END CAPS COVERING THE SEAT BOLTS, IF APPLICABLE.

2.

REMOVE FRONT SEATBOLTS, IN SOME CASES REMOVING OR LOOSENING REAR SEATBOLTS WILL EASE 

3.

THE INSTALLATION PROCESS. KEEP THE SEATBOLTS FOR RE-INSTALLATION. ON VAN HDMS THE LEFT SIDE 

FRONT & REAR BOLTS ON THE PASSENGER SEAT SHOULD BE REMOVED ( HDM MOUNT ATTACHES TO 

THE SIDE SEAT BOLTS).  

IF OFFSET MOUNT IS SUPPLIED, IT'S RECOMMENDED TO INSTALL THIS AS THE LAST PROCESS. (SEE STEP 2)

4.

SEE THE RECOMMENDED INSTALL GUIDELINES LISTED BELOW TO IDENTIFY WHICH IS BEST FOR YOUR 

5.

INSTALLATION. IF THE HDM BASE IS NOT LISTED IT EITHER HAS ITS OWN SPECIFIC INSTRUCTION OR 

FOLLOWS THE SAME PROCESS AS FIGURE 1.

VISIT US AT www.havis.com TO SEE PICTURES OF INDIVIDUALLY INSTALLED PRODUCTS.

6.

INSPECT ALL AREAS BEFORE DOING ANY DRILLING 

1.

ENSURE NO SERIOUS DAMAGE HAPPENS TO THE 

VEHICLE.

SECURE THE MOUNT WITH SUPPLIED HARDWARE KIT.

2.

75 JACKSONVILLE RD,

WARMINSTER, PA. 18974

1-800-524-9900

SIZE

TITLE:

DWG.  NO.

REV

C-HDM-100-INST

4/6/10

HAVIS, INC.

INSTALLATION INSTRUCTIONS, 

C-HDM-100's MOUNTING BASE