Havis PKG-PSM-203 User Manual
E-
ATTACHING THE SHAFT STOP
COLLAR THAT COMES WITH
TELESCOPING POLE WITH HANDLE
SLIDE THE INNER POLE TO THE DESIRED HEIGHT.
1.
ATTACH THE SHAFT COLLAR USING THE HARDWARE
2.
PROVIDED.
INNER POLE SHOULD NOW SPIN FREELY WHILE
3.
MAINTAINING THE DESIRED HEIGHT.
B-
C-HDM-401 SUPPORT ARM
LOOSELY ATTACH SPIDER (CLAMP) COLLAR TO
1.
POLE WITH HARDWARE SUPPLIED (IF NOT ALREADY
ATTACHED). POSITION AS DESIRED AND TIGHTEN
HARDWARE.
LOOSELY ATTACH C-HDM-401 USING HARDWARE
2.
PROVIDED.
FIND A SUITABLE LOCATION TO ATTACH THE OTHER
3.
END OF THE SUPPORT ARM. SOME VEHICLES HAVE
HOLES UNDER THE DASH OR OEM HARDWARE THAT
CAN BE UTILISED. LOOSELY ATTACH TAB PROVIDED.
EXTEND THE ARM ATTACHING THE TAB TO THE
4.
SUPPORT ARM WITH THE HARDWARE PROVIDED.
TIGHTEN ALL HARDWARE.
5.
C-
C-HDM-404 SUPPORT ARM
THE C-HDM-404 IS PRIMARILY USED FOR UNIVERSAL
1.
FLOOR MOUNTS WHEN PREMIUM STRENGTH / 3
POINT MOUNTING IS NECESSARY.
COMPLETE SECTION B.
2.
LOOSELY ATTACH C-HDM-404 USING HARDWARE
3.
PROVIDED.
THE MAJORITY OF HAVIS BASES HAVE AN EXTRA PEM
4.
IN ORDER TO ATTACH TO THE SUPPORT ARM. IF NOT
FIND ANOTHER LOCATION OR DRILL AND THROUGH
BOLT THE TAB BRACKET.
EXTEND THE SUPPORT ARM AND ATTACH WITH
5.
SUPPLIED HARDWARE.
TIGHTEN ALL HARDWARE.
6.
F-
EXAMPLE OF A FINISHED ASSEMBLY
THE ABOVE ASSEMBLY INCLUDES A C-HDM-102, C-
1.
HDM-202, C-MD-102, C-HDM-403, C-HDM-404(2X)
D-
C-HDM-417 VERTICAL
PRINTER MOUNT SHOWN
WITH C-PM-101 ATTACHED
A-
C-HDM-403 HORIZONTAL PRINTER
MOUNT
LOOSELY ATTACH SPIDER (CLAMP) COLLAR TO
1.
POLE WITH HARDWARE SUPPLIED (IF NOT ALREADY
ATTACHED). POSITION AS DESIRED AND TIGHTEN
HARDWARE.
ATTACH C-HDM-403 PLATE USING HARDWARE
2.
PROVIDED. AVOID TIGHTENING SCREWS IF AN
OFFSET ARM IS TO BE ADDED.
ATTACH DESIRED ITEM TO SHELF BRACKET.
3.
THE C-HDM-403 WORKS VERY WELL IF THERE IS NO
4.
CENTER CONSOLE. SPACE IS VERY LIMITED AND WILL
CAUSE LACK OF LEG ROOM IF THE VEHICLE DOES
HAVE A CENTER CONSOLE.
STEP 4 HDM VEHICLE MOUNTING AND
INSTALLATION OF OPTIONAL ACCESSORIES
D-
C-HDM-417 VERTICAL PRINTER MOUNT
COMPLETE SECTION B.
1.
LOOSELY ATTACH C-HDM-417 BRACKET USING THE
2.
HARDWARE PROVIDED.
SLIDE TWO CARRIAGE BOLTS IN THE C-PM-101 SLOTS.
3.
LOCATE THE TWO HOLES IN THE C-HDM-417
4.
BRACKET PUSH THE CARRIAGE BOLTS THROUGH THE
HOLES AND FINGER TIGHTEN THE SERRATED NUTS
PROVIDED.
SLIDE THE PRINTER TO THE RIGHT POSITION AND
5.
TIGHTEN ALL HARDWARE.
75 JACKSONVILLE RD,
WARMINSTER, PA. 18974
1-800-524-9900
SIZE
DO NOT SCALE DRAWING
TITLE:
DWG. NO.
REV
A
C-HDM-400-INST
4/6/10
HAVIS, INC.
C-HDM INSTALLATION INSTRUCTIONS