Stratasys P430 350-80100 Leaflet
Product codes
350-80100
©2014 Stratasys Inc. All rights reserved. Stratasys, Dimension, uPrint, Catalyst, FDM, Dimension BST, Dimension SST, WaveWash, and
Ecoworks are registered trademarks of Stratasys Inc. FDM Technology, Fused Deposition Modeling, uPrint Plus, uPrint SE, uPrint SE
Plus, ABSplus, Catalyst EX, and Smart Supports are trademarks of Stratasys, Inc. All other trademarks are the property of their respective
owners, and Stratasys assumes no responsibility with regard to the selection, performance, or use of these non-Stratasys products. Product
specifications subject to change without notice. Printed in the USA. SSYS-ABSplusP430-MaterialSpecSheet-EN-09-14
Stratasys | www.stratasys.com | info@stratasys.com
7665 Commerce Way
Eden Prairie, MN 55344
+1 888 480-3548 (US Toll Free)
+1 952 937-3000 (Intl)
+1 952 937-0070 (Fax)
Eden Prairie, MN 55344
+1 888 480-3548 (US Toll Free)
+1 952 937-3000 (Intl)
+1 952 937-0070 (Fax)
2 Holtzman St
Science Park, PO Box 2496
Rehovot 76124, Israel
+972 74 745-4000
+972 74 745-5000 (Fax)
Science Park, PO Box 2496
Rehovot 76124, Israel
+972 74 745-4000
+972 74 745-5000 (Fax)
ABS
plus
TM
-P430
System Availability
Layer Thickness Capability
Support Structure
Available Colors
uPrint
®
SE™
uPrint SE Plus™
Dimension
®
Elite™
Dimension SST 1200es™
Dimension BST 1200es™
Fortus
®
250mc™
0.013 inch (0.330 mm)
0.010 inch (0.254 mm)
0.007 inch (0.178 mm)
5
Soluble Supports
Breakaway Supports
(BST 1200es only)
Ivory
6
White
Black
Dark Grey
Red
Blue
Olive Green
Nectarine
Fluorescent Yellow
The information presented are typical values intended for reference and comparison purposes only. They should not be used for design specifications or quality control
purposes. End-use material performance can be impacted (+/-) by, but not limited to, part design, end-use conditions, test conditions, color etc. Actual values will vary with
build conditions. Product specifications are subject to change without notice.
The performance characteristics of these materials may vary according to application, operating conditions, or end use. Each user is responsible for determining that the
The performance characteristics of these materials may vary according to application, operating conditions, or end use. Each user is responsible for determining that the
Stratasys material is safe, lawful, and technically suitable for the intended application, as well as for identifying the proper disposal (or recycling) method consistent with
applicable environmental laws and regulations. Stratasys makes no warranties of any kind, express or implied, including, but not limited to, the warranties of merchantability,
fitness for a particular use, or warranty against patent infringement.
1
Build orientation is on side long edge.
2
Literature value unless otherwise noted.
3
Due to amorphous nature, material does not display a melting point.
4
All Electrical Property
values were generated from the average of test plaques built with default part density (sparse). Test plaques were 4.0 x 4.0 x 0.1 inches (102 x 102 x 2.5 mm) and were built
both in the flat and vertical orientation. The range of values is mostly the result of the difference in properties of test plaques built in the flat vs. vertical orientation.
5
0.007 inch
(0.178 mm) layer thickness available on Dimension Elite and Fortus 250mc only.
6
Ivory is the only color option for uPrintSE. The test data was collected using ABSplus Ivory
(Natural) specimens. ABSplus colored materials will have similar properties, but can vary up to 10%. \
Orientation: See Stratasys Testing white paper for more detailed description of build orientations.
• XZ = X or “on edge”
• XY = Y or “flat”
• ZX = or “upright”
Other
2
Test Method
Value
Specific Gravity
ASTM D792
1.04
Flame Classification
UL94
HB (0.09", 2.50mm)
UL File Number
- - - - - - - - -
E345258
Rockwell Hardness
ASTM D785
109.5