Renkforce 1007585 User Manual

•   Since there is no supporting battery, the pump output and thus the water volume 

transported through the sprinkler attachment is directly according to the intensity of 

the solar irradiation on the solar module. 

   Therefore, it will not function when it is very cloudy, in the dusk or at dawn or night.
•   The pump automatically works at sufficient solar irradiation. It cannot be switched 

on/off.

   To deactivate the pump temporarily, disconnect the connection cable from the solar 

module. You can also cover the solar module with a light-impermeable cover.

•   The pump is not protected against running dry. Therefore, always ensure that the 

pump is under water.

•   If the water‘s splashing is annoying, use a different sprinkler attachment or shorten 

the riser.

Depending on water contamination (algae, suspended particles, etc.), the pump and 

sprinkler inserts must be cleaned regularly.
Proceed as follows:
1.   First disconnect the plug connections between the pump and solar module to avo-

id inadvertent start-up.

2.   Pull  the  front  housing  part  off  forwards; 

see  arrow  in  the  figure  on  the  right.  The 

filter can then be taken out.

3.  Pull the bottom off forward like a carriage.

4.   Turn  the  front  pump  cover  to  the  left  by 

about 45°.

5.   Take off the pump cover and pull the impel-

ler out of the pump with its bearing shaft. 

6.  Take off the seal.  

7.   Remove a rubber stopper from the bearing 

shaft and pull it out of the impeller.

8.   Clean  all  parts  carefully  now.  Flush  them 

under clear water. 

9.   Now  reinstall  all  parts  in  reverse  order. 

Observe that the bearing shaft in the pump 

and in the front pump cover is placed cor-

rectly. Otherwise, the pump cover cannot 

be closed. 

 

Do not apply any force when installing the device. Else the pump may be 

damaged.

G   Operating Instructions

The product comprises of a solar module and a pump operated with it. At sufficient 

solar irradiation on the solar module, enough power is generated to operate the pump. 

Since  there  is  no  rechargeable  battery,  the  pump  runs  only  when  there  is  enough 

sunlight during the day.
Several water fountains are possible due to several enclosed nozzle attachments.
Any use other than that described above is not permitted. The safety and assembly 

notes in these operating instructions must be observed! 
This  product  complies  with  the  statutory  national  and  European  requirements.  All 

company names and product names are trademarks of their respective owners. All 

rights reserved.

•  Pump
•  Solar module
•  Ground stake for solar module
•  Extension pipe and several sprinkler attachments for the pump
•  Operating instructions

 

•   For  safety  and  approval  reasons  (CE),  unauthorised  conversion  and/or 

modification of the device are not permitted.

 

•  This product is not a toy and must be kept out of the reach of children!

 

•   The product must not be used to transport potable water or other foods.

 

•   The pump is not protected against running dry. It must be operated in wa-

ter at all times. Otherwise, it will be destroyed.

 

•   Place the solar module so that you cannot trip over it. This also applies 

when placing the cable between the solar module and the pump.

 

•   Do not step on the cable. Do not run over it with vehicles. Place the cable 

so that it cannot be damaged by sharp edges.

 

•   Do not use the product anymore if it has any damage, but dispose of it 

environmentally compatibly.

 

•   Do not leave packaging material unattended. It may become a dangerous 

toy for children.

   If there is a protective foil for transport on the solar module, remove it now.

•  Unroll the connection cable of the pump.
•   Push the extension tubes onto the pump and then put one of the sprinkler attach-

ments on the top end of the extension tube.

•  Place the pump vertically, e.g. in a garden pond. 

   Never put the pump directly into the bottom of the pond, but, e.g., on a few stones. 

Otherwise, a lot of sludge and dirt will get into the pump. This clogs the filter and 

the sprinkler attachment within seconds and thus prevents it from working.

•   Connect the plug at the end of the pump cable to the connection at the back of the 

solar module and screw on the sealing ring.

•   The surface of the solar module should be vertically aligned with the sun for best 

output power. 

   Use, e.g., the enclosed standing base that can be attached to the back of the solar 

module. Push the standing base, e.g. into the grass or a flower bed. Never hammer 

it into the ground with a tool (e.g. a hammer), though. This would destroy it. Loss of 

warranty/guarantee!

  Place the solar module so that it is located in a sunny, not shadowed location.