Microchip Technology IC PIC MCU PIC18F65J15-I/PT TQFP-64 MCP PIC18F65J15-I/PT Data Sheet
Product codes
PIC18F65J15-I/PT
PIC18F87J10 FAMILY
DS39663F-page 222
© 2009 Microchip Technology Inc.
19.4.5
GENERAL CALL ADDRESS
SUPPORT
SUPPORT
The addressing procedure for the I
2
C bus is such that
the first byte after the Start condition usually
determines which device will be the slave addressed by
the master. The exception is the general call address
which can address all devices. When this address is
used, all devices should, in theory, respond with an
Acknowledge.
The general call address is one of eight addresses
reserved for specific purposes by the I
determines which device will be the slave addressed by
the master. The exception is the general call address
which can address all devices. When this address is
used, all devices should, in theory, respond with an
Acknowledge.
The general call address is one of eight addresses
reserved for specific purposes by the I
2
C protocol. It
consists of all ‘0’s with R/W = 0.
The general call address is recognized when the
General Call Enable bit, GCEN, is enabled
(SSPxCON2<7> set). Following a Start bit detect, 8 bits
are shifted into the SSPxSR and the address is
compared against the SSPxADD. It is also compared to
the general call address and fixed in hardware.
The general call address is recognized when the
General Call Enable bit, GCEN, is enabled
(SSPxCON2<7> set). Following a Start bit detect, 8 bits
are shifted into the SSPxSR and the address is
compared against the SSPxADD. It is also compared to
the general call address and fixed in hardware.
If the general call address matches, the SSPxSR is
transferred to the SSPxBUF, the BF flag bit is set
(eighth bit) and on the falling edge of the ninth bit (ACK
bit), the SSPxIF interrupt flag bit is set.
When the interrupt is serviced, the source for the
interrupt can be checked by reading the contents of the
SSPxBUF. The value can be used to determine if the
address was device specific or a general call address.
In 10-bit mode, the SSPxADD is required to be updated
for the second half of the address to match and the UA
bit is set (SSPxSTAT<1>). If the general call address is
sampled when the GCEN bit is set, while the slave is
configured in 10-Bit Addressing mode, then the second
half of the address is not necessary, the UA bit will not
be set and the slave will begin receiving data after the
Acknowledge (Figure 19-17).
transferred to the SSPxBUF, the BF flag bit is set
(eighth bit) and on the falling edge of the ninth bit (ACK
bit), the SSPxIF interrupt flag bit is set.
When the interrupt is serviced, the source for the
interrupt can be checked by reading the contents of the
SSPxBUF. The value can be used to determine if the
address was device specific or a general call address.
In 10-bit mode, the SSPxADD is required to be updated
for the second half of the address to match and the UA
bit is set (SSPxSTAT<1>). If the general call address is
sampled when the GCEN bit is set, while the slave is
configured in 10-Bit Addressing mode, then the second
half of the address is not necessary, the UA bit will not
be set and the slave will begin receiving data after the
Acknowledge (Figure 19-17).
FIGURE 19-17:
SLAVE MODE GENERAL CALL ADDRESS SEQUENCE
(7 OR 10-BIT ADDRESSING MODE)
(7 OR 10-BIT ADDRESSING MODE)
SDAx
SCLx
S
SSPxIF
BF (SSPxSTAT<0>)
SSPOV (SSPxCON1<6>)
Cleared in software
SSPxBUF is read
R/W = 0
ACK
General Call Address
Address is compared to General Call Address
GCEN (SSPxCON2<7>)
Receiving Data
ACK
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
D7
D6
D5
D4
D3
D2
D1
D0
after ACK, set interrupt
‘0’
‘1’