Microchip Technology IC PIC MCU PIC18F65J15-I/PT TQFP-64 MCP PIC18F65J15-I/PT Data Sheet
Product codes
PIC18F65J15-I/PT
© 2009 Microchip Technology Inc.
DS39663F-page 243
PIC18F87J10 FAMILY
20.1
Baud Rate Generator (BRG)
The BRG is a dedicated 8-bit or 16-bit generator that
supports both the Asynchronous and Synchronous
modes of the EUSART. By default, the BRG operates
in 8-bit mode; setting the BRG16 bit (BAUDCONx<3>)
selects 16-bit mode.
The SPBRGHx:SPBRGx register pair controls the period
of a free-running timer. In Asynchronous mode, bits
BRGH (TXSTAx<2>) and BRG16 (BAUDCONx<3>) also
control the baud rate. In Synchronous mode, BRGH is
ignored. Table 20-1 shows the formula for computation of
the baud rate for different EUSART modes which only
apply in Master mode (internally generated clock).
Given the desired baud rate and F
supports both the Asynchronous and Synchronous
modes of the EUSART. By default, the BRG operates
in 8-bit mode; setting the BRG16 bit (BAUDCONx<3>)
selects 16-bit mode.
The SPBRGHx:SPBRGx register pair controls the period
of a free-running timer. In Asynchronous mode, bits
BRGH (TXSTAx<2>) and BRG16 (BAUDCONx<3>) also
control the baud rate. In Synchronous mode, BRGH is
ignored. Table 20-1 shows the formula for computation of
the baud rate for different EUSART modes which only
apply in Master mode (internally generated clock).
Given the desired baud rate and F
OSC
, the nearest
integer value for the SPBRGHx:SPBRGx registers can
be calculated using the formulas in Table 20-1. From this,
the error in baud rate can be determined. An example
calculation is shown in Example 20-1. Typical baud rates
and error values for the various Asynchronous modes
are shown in Table 20-2. It may be advantageous to use
be calculated using the formulas in Table 20-1. From this,
the error in baud rate can be determined. An example
calculation is shown in Example 20-1. Typical baud rates
and error values for the various Asynchronous modes
are shown in Table 20-2. It may be advantageous to use
the high baud rate (BRGH = 1) or the 16-bit BRG to
reduce the baud rate error, or achieve a slow baud rate
for a fast oscillator frequency.
Writing a new value to the SPBRGHx:SPBRGx regis-
ters causes the BRG timer to be reset (or cleared). This
ensures the BRG does not wait for a timer overflow
before outputting the new baud rate.
reduce the baud rate error, or achieve a slow baud rate
for a fast oscillator frequency.
Writing a new value to the SPBRGHx:SPBRGx regis-
ters causes the BRG timer to be reset (or cleared). This
ensures the BRG does not wait for a timer overflow
before outputting the new baud rate.
20.1.1
OPERATION IN POWER-MANAGED
MODES
MODES
The device clock is used to generate the desired baud
rate. When one of the power-managed modes is
entered, the new clock source may be operating at a
different frequency. This may require an adjustment to
the value in the SPBRGx register pair.
rate. When one of the power-managed modes is
entered, the new clock source may be operating at a
different frequency. This may require an adjustment to
the value in the SPBRGx register pair.
20.1.2
SAMPLING
The data on the RXx pin (either RC7/RX1/DT1 or
RG2/RX2/DT2) is sampled three times by a majority
detect circuit to determine if a high or a low level is
present at the RXx pin.
RG2/RX2/DT2) is sampled three times by a majority
detect circuit to determine if a high or a low level is
present at the RXx pin.
TABLE 20-1:
BAUD RATE FORMULAS
Configuration Bits
BRG/EUSART Mode
Baud Rate Formula
SYNC
BRG16
BRGH
0
0
0
8-Bit/Asynchronous
F
OSC
/[64 (n + 1)]
0
0
1
8-Bit/Asynchronous
F
OSC
/[16 (n + 1)]
0
1
0
16-Bit/Asynchronous
0
1
1
16-Bit/Asynchronous
F
OSC
/[4 (n + 1)]
1
0
x
8-Bit/Synchronous
1
1
x
16-Bit/Synchronous
Legend: x = Don’t care, n = value of SPBRGHx:SPBRGx register pair