Microchip Technology XLP 8-BIT Development Board DM240313 DM240313 Leaflet
Product codes
DM240313
XLP 8-Bit Development Kit Quick Start Guide
Program Layout
XLP 8-Bit Welcome Screen – [2 sec]
•
Button Layout – Display button function layout [2 sec]
•
Initial Clock Setup – Set up clock. Increase hours and minutes; starts in global time.
•
Main Menu – [2 Sec] lntroduction screen. Select demonstration mode.
• Active Mode – Run current mode. CPU on; peripherals on.
• With CPU on and peripherals on, the chip is at full strength. In this mode it will
show clock, temperature, frequency, brightness scale and alarm indicator.
• Exit Condition: Select [RB1] or Alarm.
• Conserve Mode – Idle current mode. CPU off; peripherals on.
• With CPU off and peripherals on, the current consumption is minimized while
keeping track of time. Dependent upon settings (wake-up, display length], the
CPU will wake up and enter Active mode for a set amount of time before return-
ing to Sleep.
CPU will wake up and enter Active mode for a set amount of time before return-
ing to Sleep.
• Exit Condition: Select [RB1] or Alarm.
• Sleep Mode – Sleep current mode. CPU off; peripherals off.
• With CPU off and peripherals off, current consumption is at a minimal. The
device is no longer able to keep track of time. Only outside interrupts will wake it
from Sleep.
from Sleep.
• Exit Conditions: Select [RB1]
•
Settings Menu – [2 Sec] Introduction screen. Select custom settings.
• Time – Custom time-related settings.
• Set Time – Adjust hours and minutes.
• Time Standard – Select [24 – HR] or [12 – HR] time standard.
• Set Alarm – Select 30 or 60 minute nap alarm; set custom time for alarm.
• Alarm Toggle – Enable/Disable alarm.
• Wake-up Interval – Used in conserve mode. Select to wake up every 15, 30 or
• Time Standard – Select [24 – HR] or [12 – HR] time standard.
• Set Alarm – Select 30 or 60 minute nap alarm; set custom time for alarm.
• Alarm Toggle – Enable/Disable alarm.
• Wake-up Interval – Used in conserve mode. Select to wake up every 15, 30 or
50 seconds, or do not wake up.
• Display Length – When woken up, display for 5 or 10 seconds. Disabled if
none.
none.
• Frequency
• 32 kHz – Run at 32 kHz; LFINTOSC
• 500 kHz – Run at 500 kHz; MFINTOSC
• 4 MHz – Run at 4 MHz; HFINTOSC
• 32 MHz – Run at 8 MHz with PLL enabled; HFINTOSC + PLL
• 500 kHz – Run at 500 kHz; MFINTOSC
• 4 MHz – Run at 4 MHz; HFINTOSC
• 32 MHz – Run at 8 MHz with PLL enabled; HFINTOSC + PLL
• Temperature
• Display Temperature – Display temperature in Celsius or Fahrenheit.
• Temperature Standard – Choose Celsius or Fahrenheit for display.
• Temperature Standard – Choose Celsius or Fahrenheit for display.
• LCD
• Backlight Toggle – Enable/Disable LCD backlight.
• Adjust Brightness – Adjust brightness of backlight.
• Adjust Brightness – Adjust brightness of backlight.
• Save Custom – Save Settings to EEPROM.
XLP 8-Bit Development Board
Jumper Setup
1. USB power connector
2. External power connector
3. Current measurement pins [Board)
4. Power Analyzer header
5. Current measurement pins [MCU)
6. LEDs
7. POT
8. PICkit™ programming header
9. SAP switch
10. SAP protocol switch
2. External power connector
3. Current measurement pins [Board)
4. Power Analyzer header
5. Current measurement pins [MCU)
6. LEDs
7. POT
8. PICkit™ programming header
9. SAP switch
10. SAP protocol switch
11. Serial Accessory Port [SAP)
12. PICtail™ connector
13. Microcontroller PIM socket
14. Generous prototyping area
15. Temperature Sensor
16. Push Buttons (3)
17. LCD with backlight
18. Battery holder
19. Harvester connector
12. PICtail™ connector
13. Microcontroller PIM socket
14. Generous prototyping area
15. Temperature Sensor
16. Push Buttons (3)
17. LCD with backlight
18. Battery holder
19. Harvester connector
DS51973A