Microchip Technology DM183021 Data Sheet
2010 Microchip Technology Inc.
DS39616D-page 251
PIC18F2331/2431/4331/4431
21.4
A/D Voltage References
If external voltage references are used instead of the
internal AV
internal AV
DD
and AV
SS
sources, the source
impedance of the V
REF
+ and V
REF
- voltage sources
must be considered. During acquisition, currents
supplied by these sources are insignificant. However,
during conversion, the A/D module sinks and sources
current through the reference sources.
In order to maintain the A/D accuracy, the voltage
reference source impedances should be kept low to
reduce voltage changes. These voltage changes occur
as reference currents flow through the reference
source impedance.
supplied by these sources are insignificant. However,
during conversion, the A/D module sinks and sources
current through the reference sources.
In order to maintain the A/D accuracy, the voltage
reference source impedances should be kept low to
reduce voltage changes. These voltage changes occur
as reference currents flow through the reference
source impedance.
21.5
Selecting and Configuring
Automatic Acquisition Time
Automatic Acquisition Time
The ADCON2 register allows the user to select an acqui-
sition time that occurs each time an A/D conversion is
triggered.
When the GO/DONE bit is set, sampling is stopped and
a conversion begins. The user is responsible for ensuring
the required acquisition time has passed between
selecting the desired input channel and the start of
conversion. This occurs when the ACQT<3:0> bits
(ADCON2<6:3>) remain in their Reset state (‘0000’).
sition time that occurs each time an A/D conversion is
triggered.
When the GO/DONE bit is set, sampling is stopped and
a conversion begins. The user is responsible for ensuring
the required acquisition time has passed between
selecting the desired input channel and the start of
conversion. This occurs when the ACQT<3:0> bits
(ADCON2<6:3>) remain in their Reset state (‘0000’).
If desired, the ACQT bits can be set to select a
programmable acquisition time for the A/D module.
When triggered, the A/D module continues to sample
the input for the selected acquisition time, then
automatically begins a conversion. Since the
acquisition time is programmed, there may be no need
to wait for an acquisition time between selecting a
channel and triggering the A/D. If an acquisition time is
programmed, there is nothing to indicate if the
acquisition time has ended or if the conversion has
begun.
programmable acquisition time for the A/D module.
When triggered, the A/D module continues to sample
the input for the selected acquisition time, then
automatically begins a conversion. Since the
acquisition time is programmed, there may be no need
to wait for an acquisition time between selecting a
channel and triggering the A/D. If an acquisition time is
programmed, there is nothing to indicate if the
acquisition time has ended or if the conversion has
begun.
21.6
Selecting the A/D Conversion
Clock
Clock
The A/D conversion time per bit is defined as T
AD
. The
A/D conversion requires 12 T
AD
per 10-bit conversion.
The source of the A/D conversion clock is software
selectable. There are eight possible options for T
selectable. There are eight possible options for T
AD
:
• 2 T
OSC
• 4 T
OSC
• 8 T
OSC
• 16 T
OSC
• 32 T
OSC
• 64 T
OSC
• Internal RC Oscillator
• Internal RC Oscillator/4
• Internal RC Oscillator/4
For correct A/D conversions, the A/D conversion clock
(T
(T
AD
) must be as short as possible, but greater than the
minimum T
AD
(approximately 416 ns, see parameter
shows the resultant T
AD
times derived from
the device operating frequencies and the A/D clock
source selected.
source selected.
TABLE 21-2:
T
AD
vs. DEVICE OPERATING FREQUENCIES
Note:
When using external references, the
source impedance of the external voltage
references must be less than 75
source impedance of the external voltage
references must be less than 75
in order
to achieve the specified ADC resolution. A
higher reference source impedance will
increase the ADC offset and gain errors.
Resistive voltage dividers will not provide a
low enough source impedance. To ensure
the best possible ADC performance, exter-
nal V
higher reference source impedance will
increase the ADC offset and gain errors.
Resistive voltage dividers will not provide a
low enough source impedance. To ensure
the best possible ADC performance, exter-
nal V
REF
inputs should be buffered with an
op amp or other low-impedance circuit.
AD Clock Source (T
AD
)
Maximum Device Frequency
Operation
ADCS<2:0>
PIC18FXX31
PIC18LFXX31
(4)
2 T
OSC
000
4.8 MHz
666 kHz
4 T
OSC
100
9.6 MHz
1.33 MHz
8 T
OSC
001
19.2 MHz
2.66 MHz
16 T
OSC
101
38.4 MHz
5.33 MHz
32 T
OSC
010
40.0 MHz
10.65 MHz
64 T
OSC
110
40.0 MHz
21.33 MHz
RC/4
(3)
011
1.00 MHz
(1)
1.00 MHz
(2)
RC
(3)
111
4.0 MHz
(2)
4.0 MHz
(2)
Note 1:
The RC source has a typical T
AD
time of 2-6
s.
2:
The RC source has a typical T
AD
time of 0.5-1.5
s.
3:
For device frequencies above 1 MHz, the device must be in Sleep for the entire conversion or the A/D
accuracy may be out of specification unless in Single-Shot mode.
accuracy may be out of specification unless in Single-Shot mode.
4:
Low-power devices only.