Microchip Technology DM183037 Data Sheet
PIC18F97J94 FAMILY
DS30575A-page 426
2012 Microchip Technology Inc.
21.2.5
BREAK CHARACTER SEQUENCE
The EUSARTx module has the capability of sending
the special Break character sequences that are
required by the LIN/J2602 bus standard. The Break
character transmit consists of a Start bit, followed by
twelve ‘0’ bits and a Stop bit. The Frame Break charac-
ter is sent whenever the SENDB and TXEN bits
(TXSTAx<3> and TXSTAx<5>, respectively) are set
while the Transmit Shift Register is loaded with data.
Note that the value of data written to TXREGx will be
ignored and all ‘0’s will be transmitted.
The SENDB bit is automatically reset by hardware after
the corresponding Stop bit is sent. This allows the user
to preload the transmit FIFO with the next transmit byte
following the Break character (typically, the Sync
character in the LIN/J2602 specification).
Note that the data value written to the TXREGx for the
Break character is ignored. The write simply serves the
purpose of initiating the proper sequence.
The TRMT bit indicates when the transmit operation is
active or Idle, just as it does during normal transmis-
sion. See
the special Break character sequences that are
required by the LIN/J2602 bus standard. The Break
character transmit consists of a Start bit, followed by
twelve ‘0’ bits and a Stop bit. The Frame Break charac-
ter is sent whenever the SENDB and TXEN bits
(TXSTAx<3> and TXSTAx<5>, respectively) are set
while the Transmit Shift Register is loaded with data.
Note that the value of data written to TXREGx will be
ignored and all ‘0’s will be transmitted.
The SENDB bit is automatically reset by hardware after
the corresponding Stop bit is sent. This allows the user
to preload the transmit FIFO with the next transmit byte
following the Break character (typically, the Sync
character in the LIN/J2602 specification).
Note that the data value written to the TXREGx for the
Break character is ignored. The write simply serves the
purpose of initiating the proper sequence.
The TRMT bit indicates when the transmit operation is
active or Idle, just as it does during normal transmis-
sion. See
character sequence.
21.2.5.1
Break and Sync Transmit Sequence
The following sequence will send a message frame
header made up of a Break, followed by an Auto-Baud
Sync byte. This sequence is typical of a LIN/J2602 bus
master.
header made up of a Break, followed by an Auto-Baud
Sync byte. This sequence is typical of a LIN/J2602 bus
master.
1.
Configure the EUSARTx for the desired mode.
2.
Set the TXEN and SENDB bits to set up the
Break character.
Break character.
3.
Load the TXREGx with a dummy character to
initiate transmission (the value is ignored).
initiate transmission (the value is ignored).
4.
Write ‘55h’ to TXREGx to load the Sync
character into the transmit FIFO buffer.
character into the transmit FIFO buffer.
5.
After the Break has been sent, the SENDB bit is
reset by hardware. The Sync character now
transmits in the preconfigured mode.
reset by hardware. The Sync character now
transmits in the preconfigured mode.
When the TXREGx becomes empty, as indicated by
the TXxIF, the next data byte can be written to
TXREGx.
the TXxIF, the next data byte can be written to
TXREGx.
21.2.6
RECEIVING A BREAK CHARACTER
The Enhanced USART module can receive a Break
character in two ways.
The first method forces configuration of the baud rate
at a frequency of 9/13 the typical speed. This allows for
the Stop bit transition to be at the correct sampling
location (13 bits for Break versus Start bit and 8 data
bits for typical data).
The second method uses the auto-wake-up feature
described in
character in two ways.
The first method forces configuration of the baud rate
at a frequency of 9/13 the typical speed. This allows for
the Stop bit transition to be at the correct sampling
location (13 bits for Break versus Start bit and 8 data
bits for typical data).
The second method uses the auto-wake-up feature
described in
. By enabling this feature, the
EUSARTx will sample the next two transitions on
RXx/DTx, cause an RCxIF interrupt and receive the
next data byte followed by another interrupt.
Note that following a Break character, the user will
typically want to enable the Auto-Baud Rate Detect
feature. For both methods, the user can set the ABDEN
bit once the TXxIF interrupt is observed.
RXx/DTx, cause an RCxIF interrupt and receive the
next data byte followed by another interrupt.
Note that following a Break character, the user will
typically want to enable the Auto-Baud Rate Detect
feature. For both methods, the user can set the ABDEN
bit once the TXxIF interrupt is observed.
FIGURE 21-10:
SEND BREAK CHARACTER SEQUENCE
Write to TXREGx
BRG Output
(Shift Clock)
(Shift Clock)
Start Bit
Bit 0
Bit 1
Bit 11
Stop Bit
Break
TXxIF bit
(Transmit Buffer
Reg. Empty Flag)
TXx (pin)
TRMT bit
(Transmit Shift
Reg. Empty Flag)
SENDB bit
(Transmit Shift
Reg. Empty Flag)
SENDB sampled here
Auto-Cleared
Dummy Write