Svs Nachrichtentechnik 01274.94 433MHz Radio Component 01274.94 Data Sheet
Product codes
01274.94
SHR-12 X4 / 01274.94
Relay board for Radio Receiver CX-12 R
12V Relay board for Radio Receiver
Operating Instructions (GB)
These operating instructions form an integral part of this product and contain important information on how to commission, install and operate it.
They must be taken into consideration and given to the end user or other third party when the installer hands over the product. These operating
instructions must be retained for future reference.
Caution! Please read! Before beginning to commission the product it is essential that this operating instruction manual is read and understood
completely. It contains instructions for operation and installation and advises about possible hazards and risks.
They must be taken into consideration and given to the end user or other third party when the installer hands over the product. These operating
instructions must be retained for future reference.
Caution! Please read! Before beginning to commission the product it is essential that this operating instruction manual is read and understood
completely. It contains instructions for operation and installation and advises about possible hazards and risks.
Validity: 03/2012; subject to change without notice
Ensure that the product is isolated from any power supply before opening. Opening and installation of the product must be
performed only by a qualified electrician.
performed only by a qualified electrician.
The product corresponds to Safety-Class II (without protective earth terminal) according to VDE 0700/IEC335/EN60335. The
use of flexible cable for connections must be avoided since terminal design does not incorporate stress relief. The use of
solid cable such as NYM is recommended. All connections must comply with local regulations and standards.
use of flexible cable for connections must be avoided since terminal design does not incorporate stress relief. The use of
solid cable such as NYM is recommended. All connections must comply with local regulations and standards.
The product complies with the electromagnetic compatibility (EMC) requirements of the current European guidelines. Conformity has been
established and the relevant documentation has been deposited by the manufacturer.
1 Mode of operation
established and the relevant documentation has been deposited by the manufacturer.
1 Mode of operation
SHR-12 X4 verifies coded radio frequency signals sent by corresponding transmitters and operates relay outputs on receipt of a correct signal.
The rated current for each relay is 10 A / 230 VAC maximum.
All transmitters of the series SH-12 including the module CX-12 T are suitable with SHR-12 X4
The rated current for each relay is 10 A / 230 VAC maximum.
All transmitters of the series SH-12 including the module CX-12 T are suitable with SHR-12 X4
It must be noted that for applications or installations involving wireless transmission and which could have an influence to safety of man or
machine there may be a risk of unforeseen operation from extraneous uncontrolled radio signals.
2 Safety Precautions
machine there may be a risk of unforeseen operation from extraneous uncontrolled radio signals.
2 Safety Precautions
Please read, and abide by, the recommendations contained in these operating instructions. Damage caused by incorrect
application or by failure to follow these operating instructions is not covered by warranty.
application or by failure to follow these operating instructions is not covered by warranty.
The manufacturer will under no circumstance be held responsible for further or consequential damage that may be
attributed to direct or indirect use of this product. All changes or modifications not expressly approved by the manufacturer will void
the warranty.
the warranty.
•
For reasons of safety and conformity (CE) it is not permitted to modify or change parts of the product.
Repair or any kind of soldering on the circuit board is forbidden.
Repair or any kind of soldering on the circuit board is forbidden.
•
The product should only be used in a case adequate for mains-voltage if applied!
•
Electrical devices should be out of reach of children. Please be extra careful if children are around.
•
For commercial use, compliance must be made with the recommendations and instructions of the responsible regional/national authorities.
•
Product operation and maintenance must be performed under the supervision of authorised, qualified personnel.
•
Opening the product and installation has to be performed by authorised electricians only.
•
The product must not be installed or used in places where a risk of explosion may exist.
•
The Relay Board is a state-of-the-art product. However, there is a risk of danger if installation or operation is performed by unqualified
personnel
personnel
3 Preparation
Start installing the Receiver-module CX-12 R, connecting the receiver carefully to the socket on the board. Make sure the Receiver is fixed and all
Pins are connected well (solder them). Then solder the antenna cable (173mm) in the appropriated pin (ref. Fig.)
Mount the product in a case adequate for 230V~/50Hz mains-voltage if voltages >40V are applied to the relay contacts. Space must be enough to
place all cables correctly and free from the electronic parts inside. Powered wiring must not be mounted over the electronic board.