Thunder Tiger Brushless 1:8 RC model car Electric 6403-F113 User Manual

Transmitter Antenna  
發射機天線
Battery Level Indicator  
發射機電源顯示燈
HI/LO Throttle ATV (Adjustable Travel Volume)  
高、低速油門行程調整鈕
Servo reversing switches  
正逆轉設定裝置
Steering Trim  
轉向微調鈕
Throttle Trim  
油門微調鈕
Steering D/R (Dual Rates)   
轉向大小動調整鈕
AUX Ch Button  
第三動開關

 

External Charging Jack  
充電孔

 

2.4GHz Binding / LED
2.4GHz校頻配對設定鈕
Steering Wheel  
轉向舵輪
Power Switch  
電源開關
Throttle Trigger  
油門控制板機
Battery Cover  
電池蓋

1.   Transmitter Antenna: Built-in antenna, it is not easy broken.
2.   Battery Level Indicator: Green / Red LEDs indicate the battery voltage. If the Red LED flashes, please replace the batteries.
3.   HI/LO Throttle ATV (Adjustable Travel Volume): Provide the function to let you independently preset the maximum travel of 

the throttle servo either side (high / low) of neutral.

4.   Servo reversing switches: To reverse the servo's rotation direction at the flip of the switch. The reversing switches are 

recessed into the transmitter to prevent accidental operation.

5.   Steering Trim: Adjusts the steering in small increments or decrements to run the model straight.
6.   Throttle Trim: Adjusts the throttle in small increments or decrements to shift the neutral position.
7.   Steering D/R (Dual Rates): Turn this knob left or right to adjust the amount of the steering dual rate. Right to increase dual rate 

amount and left to decrease the amount.

8.   AUX Ch Button: Provides an extra function for the control of the model. (for Cougar GP3 only)
9.   External Charging Jack: For rechargeable NiCd/NiHM battery pack on the transmitter only. 
10. 2.4GHz Binding / LED: The Binding button is located on the top of the 2.4GHz transmitter. For additional details, please refer to 

the “Binding” setting procedure (Page 6). LED indicate the RF status. The Red LED means RF funtion is not work.

11. Steering Wheel: Control the steering of the model.
12. Power Switch: Slide to turn the transmitter on or off.
13. Throttle Trigger: Pull or push to control the movement of the model.
14. Battery Cover: Slide cover to install or remove batteries.

1. 發射機天線：內建式發射機天線不容易損壞。
2. 發射機電源顯示燈：二顆LED設計顯示發射機電池殘量，若紅色LED燈閃爍時，請更換發射機電池。
3. 高、低速油門行程調整鈕：獨立調整高、低速油門行程量功能。
4. 正逆轉設定裝置：依實際使用，控制伺服機作動方向。
5. 轉向微調鈕：利用此旋鈕，調整設定轉向正確中立點位置。
6. 油門微調鈕：利用此旋鈕，調整設定油門正確中立點位置。
7. 轉向大小動調整鈕：調整轉向伺服機的行程量。
8. 第三動開關：第三動功能開關按鈕。（Cougar GP3 適用）
9. 充電孔：使用充電式電池時，可利用此充電孔，進行充電工作。
10. 2.4GHz 校頻配對設定鈕：2.4GHz之BINDING SW校頻配對設定鈕，為配對發射/接收頻率之用。更多功能設定方式請參考說明

書第

6頁“校頻配對步驟”。

11. 轉向舵輪：控制車輛轉向裝置
12. 電源開關：發射機電源開關
13. 油門控制板機：控制車輛前進或後退的裝置
14. 電池護蓋：推移電池護蓋即可取出電池進行更換。