Rexel Prostyle Cross Cut Shredder 2101809 Data Sheet

5

G

ACCO Brands Europe warrants its product/products and their parts 
against defects in materials and workmanship under normal use for a 
period of 2 years from the original date of purchase.  During this period 
we will repair or replace a defective product or part subject to the 
following warranty conditions:
The warranty applies only to defects in materials and workmanship 
under normal use and does not extend to damage to the Product or 
parts which result from:-
(a) Alteration, repair, modification or service carried out by anyone other

than an authorised ACCO service centre.

(b) Accident, neglect, abuse or misuse owing to failure to comply with

the normal operating procedures for a product of this type.

Nothing in this Warranty shall have the effect of excluding the liability of 
ACCO in respect of death and personal injury caused by the negligence 
of ACCO. This Warranty is offered (subject to these terms and conditions) 
in addition to, and does not affect your statutory rights.
These conditions shall in all respects be governed and construed in 
accordance with English Law and subject to the exclusive jurisdiction of 
the English Courts.

Register this product online at

• Do not shred continuously for more than 3 minutes (2 minutes Style

RC). When the motor has overheated, the thermal safety switch will
start working automatically. If the thermal switch trips, do not use
the machine for about 30 minutes while the thermal sensitive safety 
switch cools down so the shredder can be safely used again.

• This machine is not a toy. Keep away from children and pets.
• For indoor use only.
• Never insert fingers into the entry slot of the shredder.
• Turn the power off immediately if your hair, tie or sleeve becomes

entangled in the shredder.

• The shredder bin must be fully pushed closed for the machine to

operate.

• Empty the shredder bin when it is full otherwise the shredder’s

performance will be adversely affected. Operating the shredder with a 
full shredder bin can result in paper jamming in the cutters, which will
increase the machine’s noise level.

• Do not force down shredder paper in the bin using your feet.

m

Empty the shredder bin when the shredder paper is visible through the 
viewing window on the side of the pullout bin.

1

   Pull out the shredder bin (fully).

2

   Empty the shredder bin into a waste sack.

3

   Push the shredder bin back in ensuring it is fully closed.

• Place the paper or credit card into the centre of the entry slot -

shredding will start automatically (fig 3).

• Paper smaller than A4 in width should be placed in the middle of the

entry slot to ensure the shredder works automatically.

• The cutters will stop rotating automatically after finishing shredding
• Do not shred more than the stated sheet capacity at a time.
• If too many sheets are inserted at a time, the shredder can become

jammed. If the shredder becomes jammed, switch the button to REV  
(   ) position to clear the jam by reversing the paper. If the paper has 
become so entangled in the cutter that it can’t be reversed, turn off
the power and pull out the paper by hand. Restart with fewer sheets
and feed the non-shredded end of the paper in first.

If the paper shredder will not start, please check the following:

1

  Is the machine plugged in correctly?

2

  Is the switch pushed to the ‘ON/AUTO’ position?

3

  Is the machine jammed with paper?

4

 Has the motor overheated?

5

  Is the shredder bin fully pushed in?

In case of jammed paper, please follow the procedure below:

1

   Check if the bin is too full with paper - the bin should be emptied 

regularly to avoid paper becoming jammed in the cutters.

2

  Slide the switch to the ‘REV’ (   ) position to reverse the jammed 

paper.

3

   If the paper is so jammed that it will not come out in reverse 

function, slowly push the switch between ‘REV’ (   ) and ON/AUTO. 
Do not do this too quickly as this can damage the shredder.

4

  

WARNING – Do not under any circumstances use any metal objects 

(scissors, letter openers etc.) in an attempt to clear the entry – this
model has mains voltage inside the casing, which could cause
serious injury.

This machine does not require lubricant. Acco Brands Europe accepts no 
liability for product performance or safety should any lubricant be used 
on any part(s) of this machine.