Spektrum DX6i SPMR6630 User Manual
Product codes
SPMR6630
13
SPEKTRUM DX6i • RADIO INSTRUCTION MANUAL
EN
TIMER
The Timer function includes a timer on the Main
screen and an audible alarm. When the time
expires, 5 beeps sound every 5 seconds.
Timer DOWN – This sets a countdown (from up
to 59 minutes and 50 seconds).
Timer UP – This sets a count-up timer (up to 59 minutes and 50
seconds). The start time is programmable. The default start of
00:00 is recommended.
When the Timer function is enabled, the timer displays on the
Main screen.
You can assign the Trainer Switch, Power On or Throttle Cut
button to stop, start and reset the timer.
screen and an audible alarm. When the time
expires, 5 beeps sound every 5 seconds.
Timer DOWN – This sets a countdown (from up
to 59 minutes and 50 seconds).
Timer UP – This sets a count-up timer (up to 59 minutes and 50
seconds). The start time is programmable. The default start of
00:00 is recommended.
When the Timer function is enabled, the timer displays on the
Main screen.
You can assign the Trainer Switch, Power On or Throttle Cut
button to stop, start and reset the timer.
Note: Reset the timer by holding the assigned starter for more
than 3 seconds.
than 3 seconds.
A Timer direction (DOWN or UP) displays on Main screen
B Model memory number and name
C Optional value (Time Limit DOWN can be 59:50 to 0:00 and
B Model memory number and name
C Optional value (Time Limit DOWN can be 59:50 to 0:00 and
UP can be 0:00 to 59:50 that displays on Main screen)
D Timer start switch (TRAINER, THRO CUT or INH)
Note: Timer UP count is helpful for recording sailplane flight
time. Timer DOWN count is helpful for setting an alarm for land-
ing a powered model before receiver power fully discharges.
time. Timer DOWN count is helpful for setting an alarm for land-
ing a powered model before receiver power fully discharges.
TIMER
MDL6 MUSTANG
DOWN TIMER-06:00
SWITCH---TRAINER
List
B
A
D
C
MUSTANG
5.0V
MDL6
DN06:00
RANGE CHECK
Range Check function activates or inhibits use of the Trainer
switch to do a Range Check (which decreases transmitter output
power).
switch to do a Range Check (which decreases transmitter output
power).
A Trainer/Range Check switch position (When switch is held,
ACT shows here)
1. Move the transmitter no less than 30 paces, approximately
90 feet (27m), from the model.
2. Face the model with the transmitter held in normal flying
position.
3. Activate Range Check in the transmitter screen.
4. Pull and hold the trainer switch on the top left side of the
4. Pull and hold the trainer switch on the top left side of the
transmitter (Mode 2) or on the top right side (Mode 1). This
causes reduced power output from the transmitter.
causes reduced power output from the transmitter.
5. Model should respond to all transmitter control inputs while
the trainer switch is held.
6. If control issues exist, refer to your model’s manual for
troubleshooting guidance. When needed, contact the
appropriate Horizon Product Support office.
appropriate Horizon Product Support office.
Advanced Range Testing
An advanced range test using a Flight Log (SPM9540) is recom-
mended for models built with a large amount of conductive
material and a receiver with a data port. Refer to the Flight Log
instructions for information about Range Testing.
mended for models built with a large amount of conductive
material and a receiver with a data port. Refer to the Flight Log
instructions for information about Range Testing.
RANGE CHECK
CHECK INH
List
A
POWER SETTING
The Power Setting function adjusts transmitter power output to
conform to national standards.
Note: EU 328 is appropriate for most European countries
conforming to EU 300-328, while US 247 is for use in the
United States and countries outside the European Union (EU).The
France setting is for use in France.
NOTICE: The DX6i has a France RF setting that complies with
French regulations. Always use the France power setting when
operating the transmitter outdoors in France.
conform to national standards.
Note: EU 328 is appropriate for most European countries
conforming to EU 300-328, while US 247 is for use in the
United States and countries outside the European Union (EU).The
France setting is for use in France.
NOTICE: The DX6i has a France RF setting that complies with
French regulations. Always use the France power setting when
operating the transmitter outdoors in France.
POWER SETTING
A-EU 328
List
MODULATION TYPE
The Modulation Type function allows you to assign a DSM modu-
lation type (DSM2 or DSMX) to your transmitter.
Note: There is no option to return to list. You must choose a
modulation type in order to return to the menu
lation type (DSM2 or DSMX) to your transmitter.
Note: There is no option to return to list. You must choose a
modulation type in order to return to the menu
A Option value (DSM2 or DSMX)
MODULATION TYPE
AUTO DSM-X ENABLE
DSMX AND DSM-2
STANDARD RECEIVERS.
A