Spektrum DX6i SPMR6630 User Manual
Product codes
SPMR6630
14
SPEKTRUM DX6i • RADIO INSTRUCTION MANUAL
EN
CONTRAST
The Contrast function adjusts the image on the LCD for visibility
in sunlight. The default value is 50%.
in sunlight. The default value is 50%.
A Option value (0-100%)
CONTRAST
50%
List
A
COPY/RESET
The Copy/Reset function supports copying the active model memory
to any of the other 9 available model memories. This is useful for
setting up a model with different programming or to set up a similar
model.
to any of the other 9 available model memories. This is useful for
setting up a model with different programming or to set up a similar
model.
A
1
Option value (1-10, except for active model)
B
1
Approval to delete destination model memory information
CAUTION: Model information saved in a memory is erased
when that model memory is copied over or reset to factory
default settings.
when that model memory is copied over or reset to factory
default settings.
The RESET function removes all model programming from the cur-
rent model memory.
rent model memory.
A
2
Approval to delete model memory information, overwriting
memory with factory default settings.
NOTICE: If your DX6i was included in an RTF kit, factory default
settings will include programming. Using the RESET function will
erase this programming.
settings will include programming. Using the RESET function will
erase this programming.
COPY/RESET
MODEL 6 MUSTANG
COPY
RESET
List
A
COPY/RESET
MODEL 6 MUSTANG
COPY TO 1
SURE? NO/YES
List
A
B
MODEL SELECT
Model Select function opens a model memory for control of a
model or adjustment of saved settings. If you haven’t pro-
grammed a model memory, all settings will be at factory default.
model or adjustment of saved settings. If you haven’t pro-
grammed a model memory, all settings will be at factory default.
CAUTION: Do NOT change the model in Model Select
while operating a model. Change of the model interrupts
transmitter signal to a receiver and may cause a crash.
while operating a model. Change of the model interrupts
transmitter signal to a receiver and may cause a crash.
A Model memory number
B Model name
B Model name
MODEL SELECT
MODEL 6
MUSTANG
List
A
B
D/R & EXPO (Dual Rate & Expo)
The Dual Rate and Exponential function supports programming
of 2 control rates. Dual Rates and Expos are available for aileron,
elevator and rudder channels. Changing Dual Rate value affects
maximum control authority and sensitivity of control. Increasing
the rate increases sensitivity of the controls. Changing Expo-
nential value affects sensitivity around center (neutral). You can
control Dual and Expo rates by respective D/R switches (aileron,
elevator and rudder) or by one common switch (Aileron D/R, El-
evator D/R, Rudder D/R or the Gear switch. See COMBI SWITCH
screen for combining D/R switches to one common switch).
You can adjust dual rate values from 0–100%. Factory default
settings are 100% for switch positions 0 and 1.
of 2 control rates. Dual Rates and Expos are available for aileron,
elevator and rudder channels. Changing Dual Rate value affects
maximum control authority and sensitivity of control. Increasing
the rate increases sensitivity of the controls. Changing Expo-
nential value affects sensitivity around center (neutral). You can
control Dual and Expo rates by respective D/R switches (aileron,
elevator and rudder) or by one common switch (Aileron D/R, El-
evator D/R, Rudder D/R or the Gear switch. See COMBI SWITCH
screen for combining D/R switches to one common switch).
You can adjust dual rate values from 0–100%. Factory default
settings are 100% for switch positions 0 and 1.
Note: Refer to your model’s manual for recommended rate
settings.
settings.
Exponential values are adjustable from -100% to +100%. The
factory default setting is 0% or INH (inhibit).
factory default setting is 0% or INH (inhibit).
You can change either switch position to low or high rate by
putting the switch in the desired position and adjusting its value
in the D/R & EXPO screen.
putting the switch in the desired position and adjusting its value
in the D/R & EXPO screen.
A D/R switch position (0=low, 1=high)
B Exponential rate setting (-100 to 100%, with INH at 0)
C Rate setting (0 to 100%)
B Exponential rate setting (-100 to 100%, with INH at 0)
C Rate setting (0 to 100%)
Note: A negative (-) Expo value increases sensitivity around
neutral, and a positive (+) Expo value decreases sensitivity
around neutral. A positive value usually desensitizes control
response around neutral.
neutral, and a positive (+) Expo value decreases sensitivity
around neutral. A positive value usually desensitizes control
response around neutral.
D/R&EXPO
AILE 1 100% INH%
ELEV 1 100% INH%
RUDD 1 100% INH%
List
C
A
B