Futaba Hendheld RC 2.4 GHz No. of channels: 14 1-F8075 Data Sheet

*Needle high trim works as high trim based on the center. 

(Works like ATL trim.)

*This function is used to adjust the needle/engine rise 

characteristics during acceleration. This enables an 

acceleration function which temporarily increases the needle 

operation from the throttle stick.

  This function is used when there are symptoms of the 

mixture being too lean or too rich, which would be 

generated by sudden throttle stick inputs. 

  [Acceleration rate setting (RATE)]

*Acceleration can be adjusted for both high and low settings.

  [Damping rate setting (DUMPING)]

*The return time after operation (Dumping) can be set.

  Move the cursor to the rate item you want to 

change and touch the RTN button to switch 

to the data input mode.

  Adjust the rate by scrolling the touch sensor.

*When the RTN button is touched for one second, the rate is 

reset to the initial value.)

  Touch the RTN button to end adjustment and 

return to the cursor mode.

  [Operation point setting (ACT POS)]

*The operation point at which the acceleration setting will 

occur.  If this point is exceeded, acceleration is performed.

  Move the cursor to the [ACT POS] item and  

hold  the  throttle  stick  to  the  position  you 

want to change and touch the RTN button 

for one second.

* Operation linked with the throttle hold function, throttle cut 

function, and idle down function is possible. The throttle cut 

position can be adjusted accordingly. Set it to the full closed 

position.

  Move the cursor to the throttle cut or idle 

down  item  and  touch  the  RTN  button  to 

switch to the data input mode.

  Adjust  the  servo  position  by  scrolling  the 

touch sensor.

  Initial value: THR CUT: 17%, IDLE DOWN: 0%
  Adjustment  range:  THR  CUT:  0~50%,  IDLE 

DOWN: 0~100%

*When the RTN button is touched for one second, the rate is 

reset to the initial value.)

  Touch the RTN button to end the adjustment 

and return to the cursor mode.

*Before using this function, assign the [FUEL MIX] function 

to an unused channel in the Linkage menu [FUNCTION] .

1. Move the cursor to the [ACT] item and touch 

the RTN button to switch to the data input 

mode. 

  Select the ACT mode by scrolling the touch 

sensor. 

*The display blinks.

  Touch  the  RTN  button  to  activate  the 

function and return to the cursor mode. (ON 

is displayed.)

2. Move the cursor to the [MIX] item and touch 

the RTN button to switch to the data input 

mode. 

  Select the mixing mode you want to change 

by scrolling the touch sensor. 

*The display blinks.

  Touch the RTN button to change the mode 

and return to the cursor mode.

*When [MIX] is selected at the [MIX] icon, the throttle curve 

data that is set becomes the mix master. When [UNMIX] is 

selected, the throttle stick position becomes the master.

1. Move the cursor to the point rate setting item 

you want to adjust and touch the RTN button 

to switch to the data input mode.

  Adjust the rate by scrolling the touch sensor.
  Initial value: 0%
  Adjustment range: -100%~+100%

*When the RTN button is touched for one second, the servo 

operation position is reset to the initial value.)

  Touch the RTN button to end adjustment and 

return to the cursor mode.

2. Repeat this procedure for each point.

1. Move  the  cursor  to  the  needle  high  trim 

selection item and access the switch setup 

screen by touching the RTN button. Select 

the needle high trim lever.

*For a detailed description of the setting method, see [Switch 

Setting Method] at the back of this manual.

2. Move the cursor to the TRIM rate item and 

touch the RTN button to switch to the data 

input mode.

  Adjust the trim rate by scrolling the touch 

sensor.

  Initial value: 0%
  Adjustment range: -30%~+30%

*When the RTN button is touched for one second, the rate is 

reset to the initial value.)

  Touch the RTN button to end adjustment and 

return to the cursor mode.