Graupner Hendheld RC 2.4 GHz No. of channels: 12 33124 Data Sheet
Product codes
33124
203
Detail program description - Control adjust
Teacher transmitter
Up to twelve control functions of the teacher transmitter
"Teach" can be transferred to the pupil transmitter
"Pupil", either individually or in any combination.
The lower display line, named "Teach", therefore refers
to the transmitter controls permanently connected
to inputs 1 … 4 (dual axis stick functions for fi xed-wing
and heli model) and the CTRL 6 to 10 controls that are
assigned or can be assigned to inputs 5 … 12 (optionally
fl ight phase-specifi c) on the "Control adjust" menu.
Use the arrow keys
Up to twelve control functions of the teacher transmitter
"Teach" can be transferred to the pupil transmitter
"Pupil", either individually or in any combination.
The lower display line, named "Teach", therefore refers
to the transmitter controls permanently connected
to inputs 1 … 4 (dual axis stick functions for fi xed-wing
and heli model) and the CTRL 6 to 10 controls that are
assigned or can be assigned to inputs 5 … 12 (optionally
fl ight phase-specifi c) on the "Control adjust" menu.
Use the arrow keys
on the left or right touch pad
to select the transmitter controls from 1 to 12 (
) to
transfer to the pupil and then briefl y tap the center
SET
key on the right touch pad in each case, so as to switch
between "Teach" (Teacher)" (
between "Teach" (Teacher)" (
) and "Pupil"
(
):
2 3 4 5
BIND:
SW: –––
1
6
TRAINER /Pupil
Pupil
Teach
Teach
n/a
To be able to carry out the transfer, you must now assign
a trainer mode switch. To do so, use the arrow keys on
the left or right touch pad to move the marker frame
to the bottom left, to the right of "SW:" now assign a
switch as described in the section "Assigning transmitter
controls, switches and control switches" (page 52).
Preferably, you should utilize one of the two momentary
switches, SW 1 or SW 9, so as to be able to revert
control back to the teacher transmitter at any time:
a trainer mode switch. To do so, use the arrow keys on
the left or right touch pad to move the marker frame
to the bottom left, to the right of "SW:" now assign a
switch as described in the section "Assigning transmitter
controls, switches and control switches" (page 52).
Preferably, you should utilize one of the two momentary
switches, SW 1 or SW 9, so as to be able to revert
control back to the teacher transmitter at any time:
8 9 10
BIND:
SW:
7
9
11 12
TRAINER /Pupil
Pupil
Teach
Teach
n/a
No
pupil
signal
pupil
signal
Since at this stage of programming the wireless trainer
system no connection yet exists to a pupil transmitter,
the transmitter responds immediately to the switches
closed during the switch assignment process with
appropriate visual and audible warning notices. You
should therefore re-open the switch you have just
assigned:
system no connection yet exists to a pupil transmitter,
the transmitter responds immediately to the switches
closed during the switch assignment process with
appropriate visual and audible warning notices. You
should therefore re-open the switch you have just
assigned:
8 9 10
BIND:
SW:
7
9
11 12
TRAINER /Teach
Pupil
Teach
Teach
n/a
Note:
The switch assignment just described also determines
the transmitter used to issue the teacher and pupil
functions, respectively. For this reason, a pupil
transmitter must NEVER be assigned a switch on this
menu. The header line therefore also switches from
"TRAINER /Pupil" to "TRAINER /Teach" once a
switch has been assigned.
The switch assignment just described also determines
the transmitter used to issue the teacher and pupil
functions, respectively. For this reason, a pupil
transmitter must NEVER be assigned a switch on this
menu. The header line therefore also switches from
"TRAINER /Pupil" to "TRAINER /Teach" once a
switch has been assigned.
Using the arrow keys on the left or right touch pad, now
move the marker frame to the right, to "BIND: n/a":
move the marker frame to the right, to "BIND: n/a":
8 9 10
BIND:
SW:
7
9
11 12
TRAINER /Teach
Pupil
Teach
Teach
n/a
Binding the pupil transmitter to the teacher
transmitter
transmitter
Note:
During the bind process, the two transmitters should
not be very far apart. You may fi nd you need to change
the positions of the transmitters and then start the bind
process again.
During the bind process, the two transmitters should
not be very far apart. You may fi nd you need to change
the positions of the transmitters and then start the bind
process again.
Initiate the "BINDING" process from the pupil transmitter
by tapping the center
by tapping the center
SET
key on the right touch pad …
8 9 10
BIND:
SW:
7
9
Binding
–
11 12
TRAINER /Pupil
Pupil
Teach
Teach
… and repeat this immediately on the teacher
transmitter:
transmitter:
8 9 10
BIND:
SW:
7
9
Binding
11 12
TRAINER /Teach
Pupil
Teach
Teach
As soon as this process is complete, both screens will