Graupner Hendheld RC 2.4 GHz No. of channels: 12 33124 Data Sheet

248 Detail program description - Control adjust

menu. For example, you name the phase for the front 
switch position "normal" and "landing" for the rear 
position (or vice versa):

PHASE  ASSIGNMENT

A   B

C   D   E   F 

2

prior

combi

2 Landing

These phase names then appear in all fl ight-phase 
dependent menus and, of course, also in the base 
screen of the transmitter.
Now switch to the "Landing" fl ight phase and in the 
"Crow" line of the submenu ...

(page 160)

Elevat cur ve

BRAKE  SETTINGS

AILE

Crow
D.red

0%

0%

0%

0%

0%

WK

WK2

Landing

0%

… of the "Wing mixers" menu, set the desired throw of 
the ailerons with actuation of the C1 joystick ("brake") 
upward. Then, if applicable, switch to the "FL" column 
in order to specify the desired through of the fl aps with 
C1 actuation downward (hidden in the fi gure above). 
This fl ap position is referred to as "Crow position" or 
"Butterfl y; see also page 160.
In the line "D.red" (differentiation reduction), enter a 
value which corresponds to the value you entered or 
enter on the fi rst page of the "Wing mixers" menu in the 

Pha1
Pha2
Pha3

Name

Sw.time

Pha4
Pha5

Nor mal

Strecke

–
–

–

–



Landing

1.1s

0.1s
0.1s
0.1s

1.1s

Then you must assigned these two fl ight phases to a 
switch with which you can switch between the two fl ight 
phases during the fl ight. In this case, a single switch is 
suffi cient. It should be easy to reach, however, so that 
you can still switch between "motor" and "brake" during 
a landing approach, for  example, without having to 
release a joystick.
The assignment of the selected switch takes place in the 
menu ...

(page 134)

Select the switch symbol under "C" with one of the arrow 
keys. After briefl y pressing the central 

 key of the 

right touch pad, actuate the desired switch, such  as 
"SW 2".

PHASE  ASSIGNMENT

A   B

C   D   E   F 

1 Nor mal

2

prior

combi

Both switch positions, in other words ON (I) and OFF ( )
 are initially assigned in the bottom right of the display to 
the phase "1 normal". With one of the arrow keys, select 
this value fi eld and then, by briefl y pressing the central 

 key of the right touch pad, activate the selection list 

of the phases which you set up in the "Phase setting" 

Pha1
Pha2
Pha3

Name

ph.Tim.

Pha4
Pha5

Nor mal

Strecke

–
–

–

–



Clk 1

Landing

Then the timer is controlled through a corresponding 
control switch to be defi ned on the C1 joystick. As soon 
as you switch to the "Landing" fl ight phase, this fl ight 
phase timer is automatically stopped and hidden in the 
base screen. More about this can be found on page 142.
Now move the marking frame over the "Ph.Tim" column 
to the "Motor" column to the right. Here you can decide 
with "yes/no" in which phase the motor is controlled by 
the throttle/brake joystick and the brake system to be 
adjusted in the "Brake settings" submenu of the "Wing 
mixers" menu should be shut off (= "yes") and vice 
 versa (= "no"):

Pha1
Pha2
Pha3

Name

motor

Pha4
Pha5

Nor mal

Strecke

–
–

–

–



yes

Landing

no

Now move the marking frame once more to the right and 
enter an appropriate switching time after activation of 
the value fi eld of the "Sw.Time" column; for example: