Brother LK3-B484 Owner's Manual
221
ZE-8570,8580
16. TROUBLESHOOTING
16. FEHLERSUCHE
16. RESOLUTION DES PROBLEMES
16. LOCALIZACION DE AVERIAS
16. FEHLERSUCHE
16. RESOLUTION DES PROBLEMES
16. LOCALIZACION DE AVERIAS
139
139
–
–
159
158
141
92
162
52
50
49
–
–
–
48
53
139
158
165
166
166
–
–
80%
Problem
Possible cause
Page
8. Large degree of puckering
(excess tension)
•
Is the upper thread tension too strong?
Make the upper thread tension as weak as possible.
Make the upper thread tension as weak as possible.
•
Is the lower thread tension too strong?
Make the lower thread tension as weak as possible.
Make the lower thread tension as weak as possible.
•
Is the point of the needle broken?
If the point of the needle is broken, replace the needle.
If the point of the needle is broken, replace the needle.
•
Is the needle too thick?
Replace with as thin a needle as possible.
Replace with as thin a needle as possible.
•
Are the thread take-up spring tensions too strong?
Make the thread take-up spring tension as weak as possible.
Make the thread take-up spring tension as weak as possible.
•
Is the thread tension spring operating range too large?
Lower the position of the thread tension spring to as low a posi-
tion as possible.
Lower the position of the thread tension spring to as low a posi-
tion as possible.
•
Is the presser foot pressure too strong?
Adjust the presser foot pressure.
Adjust the presser foot pressure.
•
Is the sewing speed too fast?
Reduce the sewing speed slightly.
Reduce the sewing speed slightly.
•
Is the angle of the feed dog incorrect?
Tilt the front of the feed dog down slightly.
Tilt the front of the feed dog down slightly.
9. Lower thread is tangled at
the sewing start.
Lower
thread
thread
•
Is the bobbin spinning direction correct when the lower thread
is being pulled?
Set the bobbin so that it turns in the opposite direction to the
rotary hook.
is being pulled?
Set the bobbin so that it turns in the opposite direction to the
rotary hook.
•
Is there too much thread wound onto the bobbin?
The bobbin winding amount should not be more than 80%.
The bobbin winding amount should not be more than 80%.
•
Is the bobbin tension spring attached? (ZE-8580)
Attach the bobbin tension spring.
Attach the bobbin tension spring.
•
Is the bobbin turning smoothly?
If the bobbin is not turning smoothly, replace the bobbin.
If the bobbin is not turning smoothly, replace the bobbin.
•
Is a bobbin other than the light-alloy bobbins specified by Brother
being used? (ZE-8580)
Use only bobbins which are specified by Brother.
being used? (ZE-8580)
Use only bobbins which are specified by Brother.
Sprinning of bobbin during
thread trimming (ZE-8580)
thread trimming (ZE-8580)
10. Upper and lower threads
are breaking.
•
Is the needle bent or is the needle tip broken?
Replace the needle if it is bent or broken.
Replace the needle if it is bent or broken.
•
Is the needle properly installed?
If it is incorrect, install the needle correctly.
If it is incorrect, install the needle correctly.
•
Is the needle properly threaded?
If it is incorrect, thread the needle correctly.
If it is incorrect, thread the needle correctly.
•
Is the upper or lower thread tension too weak or too strong?
Adjust the upper thread or lower thread tension.
Adjust the upper thread or lower thread tension.
•
Is the upper thread may be loose because the thread tension
spring operating range is too small?
Adjust the position of the thread tension spring.
spring operating range is too small?
Adjust the position of the thread tension spring.
•
Is the needle and rotary hock timing incorrect?
Adjust the height of the needle bar.
Adjust the clearance between the needle and the rotary hock.
Adjust the height of the needle bar.
Adjust the clearance between the needle and the rotary hock.
•
Is the thread too thick for the needle?
Use the correct needle or the correct thread.
Use the correct needle or the correct thread.
•
Is the rotary hook, bobbin case, thread take-up lever or some
other part in the thread path damaged?
Repair the damage, or replace the part with a new one.
other part in the thread path damaged?
Repair the damage, or replace the part with a new one.
0627M
0628M
0629M
0471M