Pioneer SC-1525-K User Manual
Controlling the rest of your system
09
69
En
3
Point the two remote controls towards each other,
then press the button that will be doing the learning on
this receiver’s remote control.
The LED blinks once and flashes continuously.
this receiver’s remote control.
The LED blinks once and flashes continuously.
• The remote controls should be 3 cm (1 inch) apart.
4
Press the corresponding button on the other remote
control that is sending (teaching) the signal to this
receiver’s remote control.
If the LED lights for one second, the setting has been
successfully completed.
receiver’s remote control.
If the LED lights for one second, the setting has been
successfully completed.
1
5
To program additional signals for the current
component repeat steps 3 and 4.
To program signals for another component, exit and
repeat steps 2 through 4.
To program signals for another component, exit and
repeat steps 2 through 4.
6
Press R.SETUP to exit the programming mode.
Erasing one of the remote control
button settings
button settings
This erases one of the buttons you have programmed and
restores the button to the factory default.
restores the button to the factory default.
1
Press and hold R.SETUP, then press “7” for three
seconds.
The LED flashes continuously.
The LED flashes continuously.
• To cancel the preset setup mode press R.SETUP.
2
Press the input function button corresponding to
the command to be erased, then press ENTER.
The LED flashes once.
The LED flashes once.
3
Press and hold the button to be erased for three
seconds.
If the LED lights for one second, the erasing has been
successfully completed.
If the LED lights for one second, the erasing has been
successfully completed.
4
Repeat step 3 to erase other buttons.
5
Press R.SETUP to exit the erasing mode.
Erasing all learnt settings that are in
one input function
one input function
This operation erases all the operational settings of other
devices that have been programmed in one input
function, and restores the factory default.
devices that have been programmed in one input
function, and restores the factory default.
This function is handy for erasing all data programmed
for devices no longer being used.
for devices no longer being used.
1
Press and hold R.SETUP, then press “9” for three
seconds.
The LED flashes continuously.
The LED flashes continuously.
• To cancel the preset setup mode press R.SETUP.
2
Press and hold the input function button
corresponding to the command to be erased for three
seconds.
If the LED lights for one second, the erasing has been
successfully completed.
seconds.
If the LED lights for one second, the erasing has been
successfully completed.
Direct function
• Default setting: On
You can use the direct function feature to control one
component using the remote control while at the same
time using your receiver to play a different component.
This could let you, for example, use the remote control to
set up and listen to a CD on the receiver, and then use the
remote control to rewind a tape in your VCR while you
continue to listen to your CD player.
component using the remote control while at the same
time using your receiver to play a different component.
This could let you, for example, use the remote control to
set up and listen to a CD on the receiver, and then use the
remote control to rewind a tape in your VCR while you
continue to listen to your CD player.
When direct function is on, any component you select
(using the input function buttons) will be selected by both
the receiver and the remote control. When you turn direct
function off, you can operate the remote control without
affecting the receiver.
(using the input function buttons) will be selected by both
the receiver and the remote control. When you turn direct
function off, you can operate the remote control without
affecting the receiver.
1
Press and hold R.SETUP, then press “5” for three
seconds.
The LED flashes continuously.
The LED flashes continuously.
• To cancel the preset setup mode press R.SETUP.
2
Press the input function button for the component
you want to control.
3
Press “1” (On) or “0” (Off) to switch the direct
function mode.
If the LED lights for one second, the setting has been
successfully completed.
If the LED lights for one second, the setting has been
successfully completed.
If the LED flashes three times, the setting has failed.
4
Press R.SETUP to exit the setup.
Note
1 • Note that interference from TVs or other devices will sometimes result in the remote control learning the wrong signal.
• Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together or
farther apart.
• If the LED flashes for five seconds, it means the memory is full. See Erasing all learnt settings that are in one input function on page 69 to
erase a programmed button you’re not using to free up more memory (note that some signals may take more memory than others).
farther apart.
• If the LED flashes for five seconds, it means the memory is full. See Erasing all learnt settings that are in one input function on page 69 to
erase a programmed button you’re not using to free up more memory (note that some signals may take more memory than others).
3 cm
(1 inch)
This receiver’s
remote control
remote control
Other remote
control
control
SC-1525_UXJCB.book 69 ページ ２０１０年４月２０日 火曜日 午後７時３２分