Jabra SP-CEIL-006 User Manual

A

B

C

 

 

 

27700B S.W. Parkway Ave. 

Wilsonville, Oregon 97070-9215 

1-800-294-6400 

 

These are the installation instructions for your Digital Projector Mount. 

Included are four methods of installation. Select the method that works 

best for your viewing situation. The methods are: 

— 

best for short ceilings, eight (8’) or 

lower 

—

best for high ceilings, nine (9’) 

feet or higher * 

—

for installing the Digital Projector Mount on a 

rear wall 

—

for installing the Digital 

Projector Mount on a tabletop, shelf, or floor 

*If the required height range is greater than 12½", the optional SP-LTMT-

EXTP could be used to extend the length of the suspension adapter (see 
(N) under “Hardware Description” on the next page). For further 

information or ordering assistance, please contact us at the phone 

number and address listed at the top of this column.  

 Before You Start the Installation 

The wall, ceiling, tabletop, shelf, or floor where you want to install the 

digital projector must be capable of supporting a weight that is five (5) 

times the weight of the projector you are installing. Consult the projector’s 

documentation for weight specifications. If the wall, ceiling, tabletop, shelf, 
or floor is not strong enough to handle five (5) times the weight of the 

projector, then you must reinforce the installation environment. If you are 

unsure about the installation environment, please consider having it 

reinforced and having the projector installed by qualified personnel. 
Failure to do so could result in serious personal injury and damage to the 

projector. 

 

 

 

 

 

 

Copyright 



 by InFocus Corporation 

Wilsonville, OR. All rights reserved 

 

• 

To avoid personal injury, use only an approved projector mount. Using 
an unauthorized projector mount may lead to poor ventilation and 

projector failure. 

• 

 When installing the projector mount, keep in mind that the projector’s 
focus ring is not squarely in the center of the front of the projector, but 

offset by several inches. Make sure that when you mount the projector 

you offset the installation to match the amount of inches that the 

projector’s focus ring is offset from the center of the front of the 
projector. 

Before you start the installation process, prepare your Digital Projector by 

performing the following steps  

(F

 1). 

1. 

Turn the projector (C) upside down and place it on a clean flat 
surface, preferably on a towel. 

2. 

Locate the mounting bracket (B) and align it over the holes on the 

projector. 

3. 

Locate the three (3) 4 (mm) x 16 (mm) Phillips head screws (A). 

4.  Use the Phillips head screwdriver to secure the mounting bracket 

(B) to the projector via the three (3) Phillips head screws (A). Do 

not over-tighten the screws.

 

You need the following tools to install the Digital Projector Mount: 

• 

Phillips head screwdriver (not included) 

• 

Allen wrench (included) 

• 

Drill (for installation environment only - do not use a drill on the Digital 
Projector or the Digital Projector Mount) and drill bit to match the 
hardware for your installation environment (not included) 

• 

The commercially available hardware (F) that is required by your 
installation environment (not included)  

For image sizes based upon the projector’s distance to the screen, 

consult the ”Projected Image Size” section in your projector’s User’s 
Guide.

 

The Digital Projector Mount utilizes the following hardware. Note that the 

letters associated with the hardware on this list correspond to the letters 
listed in the instructions for each installation method. 

 

(A) Three (3) 4 (mm) x 16 (mm) Phillips head screws 

(B) One (1) mounting bracket 

 

 

 

 

 

 
(C) Digital Projector (not included 
 
(D) Ceiling structure (not included) 
 

(E) One (1) upper plate 

 

 

 
 
(F) Four (4) commercially available hardware anchors for the installation   

environment (not included) ** 

 

(G) One (1) swivel bracket (unit-attached)