Arcam AVR280 User Manual
AVR280
19
E
n
g
li
s
h
���
���
��
���
���
���
���
��
����
����
����
���
������
��
��
���
���
����
����
����
�����
������
�������
����
����
�����
�����
�����
�
�
�
�
�
�
�
�
�
�
���
����
�����
���
��
��
��
�����
��
���
CR100 Universal remote control
NOTE
Remember to install the four AAA batteries supplied
before trying to use your remote control.
Remember to install the four AAA batteries supplied
before trying to use your remote control.
The CR100 is a ‘universal’ remote that controls the AVR280 and up to
seven other devices. The instructions on this page only refer to the
control of the Arcam AVR280.
For information on using the remote control for other devices, and a
full list of its features, see the Handbook supplied with the CR100.
seven other devices. The instructions on this page only refer to the
control of the Arcam AVR280.
For information on using the remote control for other devices, and a
full list of its features, see the Handbook supplied with the CR100.
Device selection
IMPORTANT: Press the ‘AMP’ button first to
operate the AVR280.
IMPORTANT: Press the ‘AMP’ button first to
operate the AVR280.
On/Stand-by
This allows the AVR280 to be put into and taken
out of stand-by remotely.
If you do not wish to put Zone 2 into stand-by at
the same time as the main zone, press and hold
the stand-by button on the remote control for
more than 3 seconds.
This allows the AVR280 to be put into and taken
out of stand-by remotely.
If you do not wish to put Zone 2 into stand-by at
the same time as the main zone, press and hold
the stand-by button on the remote control for
more than 3 seconds.
MENU
Press to select the OSD Main menu.
Press and hold for more than three seconds to
select the ‘Set-up Menu Index’.
Press to select the OSD Main menu.
Press and hold for more than three seconds to
select the ‘Set-up Menu Index’.
TAPE
Selects Tape input for the amplifier
Selects Tape input for the amplifier
Navigation buttons
Arrow buttons allow navigation around the Basic
and Advanced Set-up menus on the AVR280.
Confirm a selection by pressing
Arrow buttons allow navigation around the Basic
and Advanced Set-up menus on the AVR280.
Confirm a selection by pressing
OK
.
SHIFT
B
to Power on
SHIFT
C
to Power off
SHIFT
E
to switch Zone 2 on
SHIFT
D
to switch Zone 2 off.
Source selection only
1
DVD input
2
CD player input
3
Television (sound) input
4
Auxiliary (line) input
5
Video Cassette Recorder input
6
Satellite decoder input
7
DAB/FM/AM tuner input
Press the relevant button once to select input.
MUTE
Press once to mute the main system. Press again
(or use
Press once to mute the main system. Press again
(or use
VOL +/–
) to un-mute.
VOLUME +/–
Adjusts the sound output.
Adjusts the sound output.
MODE
Cycles through available audio surround modes.
Cycles through available audio surround modes.
Source selection and handset configuration
DVD
DVD input/DVD commands
SAT
Satellite decoder input/SAT commands
AV
Television (sound) input/AV commands
TUN
Radio tuner input/TUN commands
AMP
Amplifier. Press first to operate the AVR280
AUX
Auxiliary (line) input/AUX commands
VCR
Video Cassette Recorder input/VCR
commands
commands
CD
CD player input/CD commands
Press the relevant button once to select input and
reconfigure the handset. Press and hold to select
the input without reconfiguring the remote.
reconfigure the handset. Press and hold to select
the input without reconfiguring the remote.
DISP (Display)
Press to cycle through Off/Dim/Bright illumination
of the front panel display
Press to cycle through Off/Dim/Bright illumination
of the front panel display
0
/
If the tuner is in Preset mode, these buttons give
the next Preset radio station down (
the next Preset radio station down (
0
) or up
(
/
). If the tuner is in Tune mode, these buttons
decrease/increase the tuning frequency.
AVR-specific controls
These buttons are described on the next page.
These buttons are described on the next page.