Arcam AVR280 User Manual
AVR280
21
E
n
g
li
s
h
Operating your AVR280
For information display we recommend you use the OSD on your TV/screen whenever possible. However,
all key information is also duplicated one line at a time on the front panel display of the AVR280.
all key information is also duplicated one line at a time on the front panel display of the AVR280.
Switching on/off
Press the
POWER
button in. After approximately two seconds, the power LED will turn green and the
current input and volume level will be shown; after a further 10 seconds, the AVR280 is ready for use.
Please wait until the unit has finished initialising before attempting to operate the AVR280. It is
recommended that if the unit is switched off, you should wait at least 10 seconds before switching the
unit back on.
Please wait until the unit has finished initialising before attempting to operate the AVR280. It is
recommended that if the unit is switched off, you should wait at least 10 seconds before switching the
unit back on.
Stand-by
The AVR280 has a stand-by mode which can be entered by pressing the green stand-by button on the
remote control. When in stand-by mode the display is blank and the power LED glows red. If you do not
wish to put Zone 2 into stand-by at the same time as the main zone, press and hold the stand-by button
on the remote control for about 3 seconds. After this time, the front-panel of the AVR280 will display the
text ‘Main Off’, before going into stand-by; the LED for Zone 2 will be illuminated to show that Zone 2 is
still operating.
When not being used, the AVR280 may be left in stand-by mode, as power consumption is low. If you
are not using your AVR280 for several days, however, we recommend you switch the unit off completely
using the front panel power button.
To switch on from stand-by, press one of the source buttons on the front panel or on the remote control,
or use the stand-by button on the remote control.
remote control. When in stand-by mode the display is blank and the power LED glows red. If you do not
wish to put Zone 2 into stand-by at the same time as the main zone, press and hold the stand-by button
on the remote control for about 3 seconds. After this time, the front-panel of the AVR280 will display the
text ‘Main Off’, before going into stand-by; the LED for Zone 2 will be illuminated to show that Zone 2 is
still operating.
When not being used, the AVR280 may be left in stand-by mode, as power consumption is low. If you
are not using your AVR280 for several days, however, we recommend you switch the unit off completely
using the front panel power button.
To switch on from stand-by, press one of the source buttons on the front panel or on the remote control,
or use the stand-by button on the remote control.
Volume control
To adjust the volume level of the loudspeakers, pre-amp outputs and headphones use the volume
control knob. The volume level is shown on the display. Note that different sources may require different
settings of the volume control to achieve the same perceived volume level.
It is important to realise that the value indicated for the volume level is not an accurate indication of
the power delivered to your loudspeakers. The AVR280 may deliver its full output power long before the
volume control reaches its maximum position, particularly when listening to heavily recorded music.
In comparison, some movie sountracks can appear to be very quiet, as many directors like to keep the
maximum levels in reserve for special effect sequences.
The volume can be controlled over a range of 100dB in 1dB steps.
control knob. The volume level is shown on the display. Note that different sources may require different
settings of the volume control to achieve the same perceived volume level.
It is important to realise that the value indicated for the volume level is not an accurate indication of
the power delivered to your loudspeakers. The AVR280 may deliver its full output power long before the
volume control reaches its maximum position, particularly when listening to heavily recorded music.
In comparison, some movie sountracks can appear to be very quiet, as many directors like to keep the
maximum levels in reserve for special effect sequences.
The volume can be controlled over a range of 100dB in 1dB steps.
Muting the volume
Pressing the
MUTE
button will mute the output of the AVR280 to the speakers and from the ‘pre-amp
out’ connectors (the output to the record loops remains unaffected). ‘MUTE’ will be shown on the display
while in this state.
Press
while in this state.
Press
MUTE
for a second time (or adjust the volume) to exit the mute state.
Front panel display
In normal operation, the display shows the current volume setting; smaller illuminated areas indicate the
audio input type (digital or analogue) and the digital stream type (if applicable). If the processing mode
changes (for example, from Dolby Pro Logic decoding to Dolby Digital 5.1), then this will be displayed ‘in
large letters’ for about 2 seconds.
audio input type (digital or analogue) and the digital stream type (if applicable). If the processing mode
changes (for example, from Dolby Pro Logic decoding to Dolby Digital 5.1), then this will be displayed ‘in
large letters’ for about 2 seconds.
Changing the display brightness (the
DISPLAY
button)
It is possible to select the illumination level of the front panel display. Press
DISPLAY
on the front panel
or
DIS
on the remote to cycle through the three illumination levels (Off/Dim/Bright).
���������������������������
��
���
���
����
����
��
��
����
������
������
��
��������
��������
����
�����
�������
����
�������
���
��
�����
������
������
����
������
������
������������������������������������������
������
� � � � � � � � � � � � �
� � � � � � �
�
� �
�����
���