Bosch Appliances Video Game Controller D9412GV2 User Manual
D9412GV2/D7412GV2 | Program Entry Guide | 2.0 GV2MAIN
EN | 53
Bosch Security Systems, Inc. | 10/08 | F01U003636-04
CC# Assign Door
When programmed to activate a relay, the
[ENTER] key cannot be used for any
[ENTER] key cannot be used for any
Default:
Blank
other function.
Relays used for this function must not be
shared with any other point, sensor reset,
control panel, or bell functions. Sharing
can cause errors in relay operation.
shared with any other point, sensor reset,
control panel, or bell functions. Sharing
can cause errors in relay operation.
Selection: 1 to 8, Blank
Blank No door controller is assigned for adding
tokens or the CLOSE DOOR # appears on
the keypad.
the keypad.
1 to 8 The door controller assigned to this keypad
is used to read new tokens when the Add
User Mode is initiated.
User Mode is initiated.
CC# Entr Cycl Dr
Default:
No
If the assigned door remains open and this keypad
has the CC# Close Door Warning Tone set to Yes,
the CLOSE DOOR # message appears on this
keypad.
has the CC# Close Door Warning Tone set to Yes,
the CLOSE DOOR # message appears on this
keypad.
Selection: Yes or No
Yes
The [ENTER] key is used to cycle the
door programmed for CC Assign
Door.
door programmed for CC Assign
Door.
• If a door is not programmed for this
No
The [ENTER] key is not used to cycle
the door.
the door.
prompt and a door is not assigned to
Enter Key Cycle Door: Program this prompt as Yes
to start the door cycle sequence for the door number
programmed in CC# Assign Door when a user
enters a valid pass code and presses [ENTER]. This
includes shunting the point assigned to the door.
ACCESS GRANTED prints on the local printer and at
the central station receiver, if programmed.
to start the door cycle sequence for the door number
programmed in CC# Assign Door when a user
enters a valid pass code and presses [ENTER]. This
includes shunting the point assigned to the door.
ACCESS GRANTED prints on the local printer and at
the central station receiver, if programmed.
• The service pass code cannot be used
for the CC# Entr Cycl Dr application.
• When programmed to activate a relay,
the [ENTER] key cannot be used for
any other function.
any other function.
• Relays used for this function must not
be shared with any other point, sensor
reset, control panel, or bell functions.
Sharing can cause errors in relay
operation.
reset, control panel, or bell functions.
Sharing can cause errors in relay
operation.
• The door does not cycle if Entr Key
Rly is programmed.
• 9210 NOT READY appears at this
keypad when you press [ENTER] if the
D9210B is not programmed with a D#
Entry Area (in the RADAXS handler)
or if CC Assign Door does not have a
door number assigned.
D9210B is not programmed with a D#
Entry Area (in the RADAXS handler)
or if CC Assign Door does not have a
door number assigned.
the area using the D# Entry Area in
the RADAXS handler, 9210 NOT
READY appears at this keypad when
you attempt to add a user. The
message indicates that the control
panel cannot start the Add User Mode
until a door is assigned to this keypad.
READY appears at this keypad when
you attempt to add a user. The
message indicates that the control
panel cannot start the Add User Mode
until a door is assigned to this keypad.
• Assigning a door to a keypad is not
necessary for the user to control the
door(s) using the Door Control
function. Any door that is active can be
controlled by a user who has the
appropriate door control authority. The
door control functions are available to
a valid user at any keypad with access
to the area where the door is
assigned.
door(s) using the Door Control
function. Any door that is active can be
controlled by a user who has the
appropriate door control authority. The
door control functions are available to
a valid user at any keypad with access
to the area where the door is
assigned.
During the Add User Mode, tokens or
cards, door control requests, and
RTE/REX do not function. Put the Door
cards, door control requests, and
RTE/REX do not function. Put the Door
Mode into an unlocked state before
adding users if there is heavy activity for
this door.
adding users if there is heavy activity for
this door.