Summit SEH26 Manual
15
8
INSTALLATION
CAUTION: During installation, persons installing the hood must wear heavy gloves
CAUTION: During installation, persons installing the hood must wear heavy gloves
to protect against sharp edges.
POSITIONING THE RANGE HOOD
Upon completion of installation, the distance between the hood and an electric
rangetop must be a minimum of 25" (65cm), and the distance between the hood and a
gas rangetop must be a minimum of 30" (75cm).
Upon completion of installation, the distance between the hood and an electric
rangetop must be a minimum of 25" (65cm), and the distance between the hood and a
gas rangetop must be a minimum of 30" (75cm).
min. 30" for gas ranges
min. 25" for electric ranges
PREPARING THE SITE
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY,
OBSERVE THE FOLLOWING:
a.
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY,
OBSERVE THE FOLLOWING:
a.
Installation work and electrical wiring must be done by quali?ed personnel in
accordance with all applicable codes and standards, including ?re-rated
construction.
accordance with all applicable codes and standards, including ?re-rated
construction.
b.
Sufficient air is needed for proper combustion and exhausting of gases through
the ?ue (chimney) of fuel-burning equipment to prevent backdrafting. Follow the
range manufacturer's guidelines and safety standards such as those published by
the National Fire Protection Association (NFPA), the American Society for
Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local
code authorities.
the ?ue (chimney) of fuel-burning equipment to prevent backdrafting. Follow the
range manufacturer's guidelines and safety standards such as those published by
the National Fire Protection Association (NFPA), the American Society for
Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local
code authorities.
c.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and
other hidden utilities.
other hidden utilities.
d.
Ducted fans must always be vented to the outdoors.
Check Electric connection.
(Supply voltage should be 1
10-120 V
, hood
should be connected to grounded socket.)
Check lamp switch.
(Lamp switch should be in on position.)
Hood does not operate
Illumination lamp
does not illuminate
does not illuminate
Air suction of
hood is weak
It does not exhaust
air(in the ambient
without chimney)
hood is weak
It does not exhaust
air(in the ambient
without chimney)
Check motor switch.
(Motor switch should be in I,II,III position)
Check aluminum filter
.
(Aluminum cassette filter should be washed once a month
under normal conditions.)
Check bulbs.
(Bulbs should be in good conditions.)
Check air outlet chimney
.
(Air outlet chimney should be open.)
Check carbon filter
.
(If it operates with carbon filter
, carbon filter should be
replaced quarterly
.)
X
X
X
X
X
X
X
X
X
X
TROUBLESHOOTING
If hood does not operate, before contacting customer service:
Be sure that the power cable is connected to the power supply and that the electric
fuse for the installation is in good condition. Before contacting the service, check
your hood according to the table below. If the problem continues, contact your dealer
or authorized service center.
Troubleshooting Guide
Be sure that the power cable is connected to the power supply and that the electric
fuse for the installation is in good condition. Before contacting the service, check
your hood according to the table below. If the problem continues, contact your dealer
or authorized service center.
Troubleshooting Guide
Service and Spare Parts
You can obtain service advice and spare parts for your product directly from
SUMMIT by calling us at 1-800-932-4267 or by going to our website at
www.summitappliance.com/support
Have the model number of your range hood handy. This can be found on the
product label, which can be seen when you remove the aluminum cassette filter.
You can obtain service advice and spare parts for your product directly from
SUMMIT by calling us at 1-800-932-4267 or by going to our website at
www.summitappliance.com/support
Have the model number of your range hood handy. This can be found on the
product label, which can be seen when you remove the aluminum cassette filter.
An exploded view, parts list and wiring diagram for your unit can be found on the
following pages of this manual.
following pages of this manual.