Marantz R3001 User Manual

ENTER

3

2

1

6

5

4

9

8

0

7

 

  Press and hold down the any Function 

Selector button and press SETUP button until 
the indicator blinking twice.

 

  Press the code 9 - 8 - 1.

 

  The indicator will blink twice.

 

  Then, RC5500SR will return to the factory 

preset code.

After this procedure, the selected function button is set 
initial code and other function buttons are set initial 
code too.

Once you have found and the codes for your vari-
ous appliances, you may want to write them down 
here.

TV

VCR

DSS

DVD

CD

TAPE

CDR

MD

ENTER

3

2

1

6

5

4

9

8

0

7

 

  Switch on the appliance which should be 

controlled.

 

  Press and hold down the Function Selector 

button for appliance which should be controlled 
and press SETUP  button  until the indicator 
blinking twice.

 

  Press the code 9 - 9 - 1.

 

  The indicator will blink twice.

 

  Aim the remote control at the appliance and 

slowly alternate between pressing POWER 
button  and the Function Selector button for 
the appliance.

 

  Stop when the appliance turns off.

 

 Press 

SETUP button once to lock in the code.

ENTER

3

2

1

6

5

4

9

8

0

7

 

  Press and hold down the Function Selector 

button for appliance which should be controlled 
and press SETUP  button until the indicator 
blinking twice.

 

  Press the code 9 - 9 - 0.

 

  The indicator will blink twice.

 

  To view the code for fi rst digit, press 1 once.

 

  Wait 3 seconds, count the indicator blinks (e.g. 

3 blinks = 3) and write down the number.

If a code digit is “0”, the indicator will not blink.

 

  Repeat step 3 three more times for remaining 

digits.  Use 2 for the second digit, 3 for the third 
digit, and 4 for the fourth digit.

The remote controller RC5500SR must be 
programmed to use the codes for your  appliances 
of different brands. This is done by keying in a 4-digit 
code or by scanning the codes until the correct one is 
found. We recommend to using the 4-digit code. This 
mode is faster and more reliable. The code scanning 
method should be used only if you cannot fi nd  the 
code for one of your appliances. The codes are listed 
at the end of this book.

Important:
•  Use the remote control buttons for programming, 

not the buttons of the receiver or other appliances.

•  Some codes may be not match your equipment. In 

this case, your equipment cannot be controlled with 
this remote controller.

ENTER

3

2

1

6

5

4

9

8

0

7

 

  Press and hold down the Function Selector 

button for the appliance which should be 
controlled and press SETUP  button  until the 
indicator blinks twice.

 

  Press the 4-digit code for appliance (code table 

at the end of this book)

 

  When the procedure is successful, the indicator 

will blink twice.

If the indicator did not blink twice, then repeat steps 1 
through 2 and try entering the same code again.

¤1  PURE DIRECT button

When this button is pressed, the tone control circuit 
is bypassed.

¤2  SETUP / T.TONE button

(when AMP mode is selected)
Used to enter the test tone menu.

¤3 OSD 

This button is unavailable for SR3001.

¤4  SLEEP (sleep timer) button

This button is used for setting the sleep timer.  It 
can be operated the same way as the button on the  
unit.

¤5  TV VOLUME UP (

3) /DOWN (4) 

These buttons increase or decrease TV’s volume.