Panasonic PT-AE1000E User Manual
Names and functions of each part
ٕ ٕ
ًٕ
٨
٨
Remote control emitter
Buttons shown in this colour are buttons that can be used for learnt functions.
Buttons that cannot be used for learnt functions LEARN, SETUP, system device selection
Buttons that cannot be used for learnt functions when using a projector (PJ) MENU, ENTER, RETURN,
Buttons that cannot be used for learnt functions when using a projector (PJ) MENU, ENTER, RETURN,
This turns the projector power
on and off when the projector's
power is turned on
on and off when the projector's
power is turned on
Liquid crystal display
Function buttons(A/B/C)
This displays menus
This returns menu adjustment
values to their factory defaults.
values to their factory defaults.
This adjusts the picture
size and focus.
size and focus.
This switches the input
source.
source.
This switches the
picture mode.
picture mode.
This switches the aspect
ratio (the ratio between
width and height of the
screen).
ratio (the ratio between
width and height of the
screen).
This displays the
input waveforms.
input waveforms.
This turns on button illumination
for the remote control.
for the remote control.
System device operation
buttons
buttons
These buttons are used for
menu screen operations.
menu screen operations.
This momentarily pauses
images.
images.
This sets the time to elapse
before the power turns off
automatically.
before the power turns off
automatically.
This displays the "MEMORY
LOAD" menu.
LOAD" menu.
This displays the "COLOUR
MANAGEMENT" menu.
MANAGEMENT" menu.
This displays the "PICTURE
ADJUSTMENT" menu.
ADJUSTMENT" menu.
Note:
̖
̖
If operating the remote control by facing it directly towards the remote control receiver at the front of the projector,
the remote control should be within approximately 7 metres of the front of the remote control receiver. In addition,
the remote control can be operated within an angle of +/- 30 degrees up, down or to the left or right.
If there are any obstructions between the remote control and the remote control receiver, the remote control may
not operate correctly.
The projector can be operated by reflecting the signals from the remote control off the screen, but the operating
range for the remote control may be reduced as a result of losses in the amount of light reflected due to the
characteristics of the screen.
the remote control should be within approximately 7 metres of the front of the remote control receiver. In addition,
the remote control can be operated within an angle of +/- 30 degrees up, down or to the left or right.
If there are any obstructions between the remote control and the remote control receiver, the remote control may
not operate correctly.
The projector can be operated by reflecting the signals from the remote control off the screen, but the operating
range for the remote control may be reduced as a result of losses in the amount of light reflected due to the
characteristics of the screen.
If no remote control operations are
carried out for 30 seconds or more,
the backlight will switch off.
Once the backlight has turned off
after 30 seconds, it can be turned
back on by pressing any button.
If you press a button to turn once
more and then press it again within
30 seconds to turn the backlight off
again, the backlight will not turn back
on again when another button (other
than "LIGHT") is pressed.
carried out for 30 seconds or more,
the backlight will switch off.
Once the backlight has turned off
after 30 seconds, it can be turned
back on by pressing any button.
If you press a button to turn once
more and then press it again within
30 seconds to turn the backlight off
again, the backlight will not turn back
on again when another button (other
than "LIGHT") is pressed.
If no remote control operations are
carried out for 30 seconds or more, the
LCD will switch off. If the LCD switches
off while the device selection indicator for
any component is flashing, the
component that was last selected will be
the one that will be operated.
carried out for 30 seconds or more, the
LCD will switch off. If the LCD switches
off while the device selection indicator for
any component is flashing, the
component that was last selected will be
the one that will be operated.
These buttons are used to operate
system devices using preset
functions for this remote control and
also functions which have been
learnt through signals from other
remote controls.
system devices using preset
functions for this remote control and
also functions which have been
learnt through signals from other
remote controls.
If you press any of the buttons marked as
Projector function only
, the device selection will switch to "PJ".
Projector function only
Projector function only
Projector function only
2 -
E
NGLISH
The top shows the selected device, the
bottom shows the functions of that device
that can be operated. (※ p.15)
bottom shows the functions of that device
that can be operated. (※ p.15)
(
※"PJ" p.15)