Casio MO0602-EA Manual De Usuario

8

• When the currently selected time zone is one that includes mostly ocean, a

value indicating the zone’s Greenwich Mean Time differential appears in
place of a city code.

• If the current time shown for a city is wrong, check your Home City time

settings and make the necessary changes.

1. In the World Time Mode, use C (east) and A

(west) to display the city code (time zone)
whose Standard Time/Daylight Saving Time
setting you want to change.

2. Hold down E to toggle between Daylight

Saving Time (DST indicator displayed) and
Standard Time (DST indicator not displayed).

• The DST indicator appears on the display

whenever you display a city code for which
Daylight Saving Time is turned on.

• You cannot toggle between Daylight Saving Time and Standard Time if the

displayed city code is 

GMT.

• Note that the DST/Standard Time setting affects only the currently

displayed city code. Other city codes are not affected.

The stopwatch lets you measure elapsed time,
split times, and two finishes.

• The display range of the stopwatch is 9 hours,

59 minutes, 59.99 seconds.

• The stopwatch continues to run, restarting from

zero after it reaches its limit, until you stop it.

• The stopwatch measurement operation

continues even if you exit the Stopwatch Mode.

• Exiting the Stopwatch Mode while a split time is

frozen on the display clears the split time and
returns to elapsed time measurement.

• All of the operations in this section are

performed in the Stopwatch Mode, which you
enter by pressing D.

Minutes

Seconds

1/100
second

Timekeeping
Mode time

Hours

First runner
finishes.
Display time
of first runner.

Display time of
second runner.

Second runner
finishes.

C

C

C

C

A

C

A

A

C

A

(sj displayed)

C

A

C

A

A

You can set a countdown timer start time in the
range of one minute to 60 minutes. An alarm
sounds when the countdown reaches zero. An
auto-repeat feature causes the countdown to
restart automatically when the end of a
countdown is reached, and a progress beeper
signals the progress of the countdown.

• All of the operations in this section are

performed in the Countdown Timer Mode,
which you enter by pressing D.

The following are the settings you should
configure before actually using the countdown
timer.

• Countdown start time

• Auto-repeat on/off

• Progress beeper on/off

Timekeeping
Mode time

You can set a countdown start time in the range of one minute to 60 minutes,
in one-minute increments.

Whenever zero is reached, the watch beeps and auto-repeat automatically
restarts the countdown from the countdown start time you set. When the
countdown reaches zero while auto-repeat is turned off, the watch will beep
and then display the countdown start time (without restarting the countdown).
Auto-repeat will repeat up to 10 times.

When the progress beeper is turned on, the watch beeps at minute 10, 5, 4,
3, 2, and 1 of the countdown, and at second 50, 40, 30, 20, 10, 5, 4, 3, 2, and
1 of the final minute of the countdown.

1. While the countdown start time is on the

display in the Countdown Timer Mode, hold
down E until the minute setting of the
countdown start time starts to flash, which
indicates the setting screen.

• If the countdown start time is not displayed,

use the procedure under “To use the
countdown timer” to display it.

2. Press D to toggle between the countdown

starting time setting screen and the auto-
repeat setting screen.

3. Perform the following operations, depending on which setting is currently

selected on the display.

• While the minute setting is flashing, use C (+) or A (–) to change it.

• While the auto-repeat on/off setting (

 or 

) is flashing on the

display, press C to toggle auto-repeat on (

) and off (

).

4. Press E to exit the setting screen.

l l l l l l

ll

ll

lll

ll

ll

ll

ll

ll

l l

Pressing A while the countdown start time is on
the display or while a countdown timer operation
is in progress in the Countdown Timer Mode
toggles progress beeper operation on (
displayed) and off (

  not displayed).

Press C while in the Countdown Timer Mode to start the countdown timer.

• When the countdown reaches zero, the alarm sounds for five seconds or

until you stop it by pressing any button.

• Press C while a countdown operation is in progress to pause it. Press C

again to resume the countdown.

Progress beeper on
indicator

• The countdown timer operation continues even if you exit the Countdown

Timer Mode.

• To stop a countdown operation completely, first pause it (by pressing C),

and then press A. This returns the countdown time to its starting value.

• Frequent use of auto-repeat and the alarm runs down the battery.

Minutes

In the World Time Mode, use C (east) and A (west) to scroll through city
codes (time zones).

World Time digitally displays the current time in
30 cities (29 time zones) around the world.

• For full information on city codes, see the “City

Code Table”.

• All of the operations in this section are

performed in the World Time Mode, which you
enter by pressing D.

Timekeeping Mode time

Current time in the zone
of the selected city code

Seconds