Hampton Direct H35-NG1 Manual De Usuario

18

Hampton

®

 H35 Direct Vent Freestanding Gas Stove

Review the following sequence of instructions 
which are typical of most installations. The se-
quence may vary depending on wall thickness. 
See "Exterior Vent Terminal Locations" to 
"Venting Arrangements" section for vent 
location and clearance dimensions, and the 
"Vent Restrictor Position" section to set the  
Vent Restrictor to the correct position.

1)  Set the unit in its desired location. Check 

to determine if wall studs will be in the way 
of the venting system, adjust location until 
all clearances are met and there are no 
obstructions.

 

b)  Install wall thimbles on both interior 

and exterior wall with 4 wood screws 
(#8 x 1") per thimble.

 

c)  Attach the 2 piece adjustable pipe sec-

tion to the vent terminal and slide into 
position from the exterior. The larger 
diameter end of the adjustable pipe 
goes to the vent terminal.

 

d)  Install the 90

o

 elbow onto the adjust-

able pipe  to determine the vertical 
centerline. 

 

e)  Cut the 4 ft. section of rigid pipe to 

length. Attach the  45

o

 elbow to the rigid 

pipe, and ensure that the pipe length 
when cut  (with the 45

o

 elbow) will seat 

onto both the starter collar and the 90

o

 

elbow.  Crimped section of rigid pipe 
seats into the 90

 

Dismantle all pipe sections including vent 
terminal.

2) Assemble 

a 

trial fi t to determine the vertical 

center-line for the vent termination.

 

a)  Cut a 9-1/2" x 9-1/2" (241mm x 241 

mm) square hole on both the interior 
and exterior wall.

DV 2 ft.  Stove Vent Kit (Part # 946-116)  and DV 4 ft. Stove Vent Kit (Part #946-216) includes all the parts 
needed to install the H35 Direct Vent unit with minimum horizontal and vertical vent dimensions. 
For installations that require longer vertical and/or horizontal vents use the Dura-Vent system as 
shown in the "Dura-Vent Termination Kit" and "Dura-Vent Venting Components" sections.

1)   

1   

Rigid Pipe Section (Kit # 946-116: 2 ft. (1.2m) length,

 

 

   

Kit # 946-216: 4 ft. (1.2m) length), 6-1/2" (165mm) 

    

  inside 

diameter 

2)   

1   

Flex Liner, compressed aluminium 2 ply liner, 4" (102mm) 

    

  inside 

diameter

3)   4  

Spring 

Spacers

4)   1  

90 

deg. 

Elbow

5)   

1   

Adjustable pipe section 13-1/2" to 24" (343mm x 610mm), 2 

pcs.

6)   1  

Thimble 

Cover

7)   1  

Wall 

Thimble 

(2 

pcs.)

8)   1  

Adapter 

9)   1  

AstroCap Termination Cap

10)  

2   

Trim Collars

11)  

1   

Tube of Mill-Pac, high temperature sealant

12)   12   

Screws, #8 x 1/2" Self tapping, Stainless Steel

13)   14   

Screws, #8 x 1/2" Self tapping, Black

14)  

4   

Screws #8 x 1-1/2" Drill Point, Black

15)  

4   

Screws #8 x 1-1/2" Drill Point, Stainless Steel

16)  

8   

Wood screws #8 x 1"

Required but not included in above Kit: 

45

o

 Elbow (Part #: 946-214)