Windsor 10052250 Manual De Usuario
MACHINE OPERATION
CUTTER 24V 86039070 04/10/07
3-11
DOUBLE SCRUB
For floors which are heavily soiled or have thick
accumulations of floor finish may not clean
sufficiently with one pass. In these cases it will be
necessary to double scrub.
To double scrub, make the first pass over the
surface being cleaned with the squeegee up,
vacuum off, the solution on, Aqua-Mizer removed
and brushes down. This allows the
accumulations of floor finish may not clean
sufficiently with one pass. In these cases it will be
necessary to double scrub.
To double scrub, make the first pass over the
surface being cleaned with the squeegee up,
vacuum off, the solution on, Aqua-Mizer removed
and brushes down. This allows the
solution to stay in
contact with the soil while loosening the surface
accumulation with the brushes. Allow time for the
first application to stay in contact with the floor.
Length of time between the first and second pass
depends on amount of accumulation and the type of
chemical being used. A second scrubbing with the
squeegee down and again the solution and brushes
on will further loosen soil. The additional application
of solution will further assist the difficult cleaning job.
accumulation with the brushes. Allow time for the
first application to stay in contact with the floor.
Length of time between the first and second pass
depends on amount of accumulation and the type of
chemical being used. A second scrubbing with the
squeegee down and again the solution and brushes
on will further loosen soil. The additional application
of solution will further assist the difficult cleaning job.
FOR SAFETY: When using machine, go slow on
inclines and slippery services.
inclines and slippery services.
EMPTYING AND CLEANING TANKS
1. Park the machine next to a floor drain. Drain
hose is on left rear corner of the machine.
2. Turn the machine power off and set parking
brake, if your machine is equipped with this
option.
option.
SOLUTION TANK
1.
Loosen small drain hose from the retainer, then
lower hose in direction of the drain.
lower hose in direction of the drain.
2. Remove the solution tank cover.
3. Flush the solution tank out with clean water and
run several gallons of clean water through
systems. Do not use water hotter than 140°F
(60°C) to clean tank. Damage may occur.
systems. Do not use water hotter than 140°F
(60°C) to clean tank. Damage may occur.
NOTE: Never allow solution to remain in tank.
Damage to tank, seals and valves could occur.
Damage to tank, seals and valves could occur.
4. Secure drain hose into the retainer.
RECOVERY TANK
1. Unhook the large drain hose from the retainer.
1. Unhook the large drain hose from the retainer.
Unscrew the T-handle on plug enough to loosen
plug, then lower hose in direction of the drain.
Do not stand in front of end of hose. Recovered
solution will come out with force. Slowly remove
plug from drain hose.
plug, then lower hose in direction of the drain.
Do not stand in front of end of hose. Recovered
solution will come out with force. Slowly remove
plug from drain hose.
2. Remove the recovery tank dome. Flush the
recovery tank out with clean water. Do not use
water hotter than 140°F (60°C) to clean tank.
Damage may occur.
water hotter than 140°F (60°C) to clean tank.
Damage may occur.
3. Clean off the float shut-off system and inspect
for free movement of float. The float shut-off
system is located in the rear of the recovery
tank.
system is located in the rear of the recovery
tank.
4. Replace the drain plug and secure drain hose in
bracket.
5.
If machine is to be stored, leave the recovery
tank dome off.
tank dome off.
SOLUTION
TANK DRAIN
TANK DRAIN
RECOVERY
TANK DRAIN
TANK DRAIN
RECOVERY
TANK COVER
TANK COVER
SOLUTION
TANK COVER
TANK COVER