Integra DHC-9.9 Manual De Usuario
124
■ Power On Volume
This setting determines what the volume will be each
time the AV controller is turned on.
This setting determines what the volume will be each
time the AV controller is turned on.
When the “Volume Display” preference is set to “Abso-
lute”, the range is “Last”, “Min”, 1 to “Max”. When it’s
set to “Relative”, the range is “Last”, –
lute”, the range is “Last”, “Min”, 1 to “Max”. When it’s
set to “Relative”, the range is “Last”, –
∞
dB, –81 dB to
+18 dB.
To use the same volume level as when the AV controller
was last turned off, select “Last”.
was last turned off, select “Last”.
Note:
The “Power On Volume” setting cannot be set higher
than the “Maximum Volume” setting.
The “Power On Volume” setting cannot be set higher
than the “Maximum Volume” setting.
■ Headphone Level
With this setting, you can offset the headphone volume
relative to the main volume. This is useful if your head-
phones are too loud or too quiet at the volume setting you
usually use when listening through your speakers. The
headphone level can be set from –12 dB to +12 dB.
With this setting, you can offset the headphone volume
relative to the main volume. This is useful if your head-
phones are too loud or too quiet at the volume setting you
usually use when listening through your speakers. The
headphone level can be set from –12 dB to +12 dB.
■ Zone2 Maximum Volume
With this setting, you can limit the maximum volume for
Zone 2.
With this setting, you can limit the maximum volume for
Zone 2.
When the “Volume Display” setting is set to “Absolute”,
the “Maximum Volume” range is “Off”, 99 to 50. When
it’s set to “Relative”, the range is “Off”, +17 dB to
–32 dB. To disable this setting, select “Off”.
the “Maximum Volume” range is “Off”, 99 to 50. When
it’s set to “Relative”, the range is “Off”, +17 dB to
–32 dB. To disable this setting, select “Off”.
■ Zone2 Power On Volume
This setting determines what the volume will be for
Zone 2 each time the AV controller is turned on.
This setting determines what the volume will be for
Zone 2 each time the AV controller is turned on.
When the “Volume Display” preference is set to “Abso-
lute”, the range is “Last”, “Min”, 1 to “Max”. When it’s
set to “Relative”, the range is “Last”, –
lute”, the range is “Last”, “Min”, 1 to “Max”. When it’s
set to “Relative”, the range is “Last”, –
∞
dB, –81 dB to
+18 dB.
To use the same volume level as when the AV controller
was last turned off, select “Last”.
was last turned off, select “Last”.
■ Zone3 Maximum Volume
With this setting, you can limit the maximum volume for
Zone 3.
With this setting, you can limit the maximum volume for
Zone 3.
When the “Volume Display” setting is set to “Absolute”,
the “Maximum Volume” range is “Off”, 99 to 50. When
it’s set to “Relative”, the range is “Off”, +17 dB to
–32 dB. To disable this setting, select “Off”.
the “Maximum Volume” range is “Off”, 99 to 50. When
it’s set to “Relative”, the range is “Off”, +17 dB to
–32 dB. To disable this setting, select “Off”.
■ Zone3 Power On Volume
This setting determines what the volume will be for
Zone 3 each time the AV controller is turned on.
This setting determines what the volume will be for
Zone 3 each time the AV controller is turned on.
When the “Volume Display” preference is set to “Abso-
lute”, the range is “Last”, “Min”, 1 to “Max”. When it’s
set to “Relative”, the range is “Last”, –
lute”, the range is “Last”, “Min”, 1 to “Max”. When it’s
set to “Relative”, the range is “Last”, –
∞
dB, –81 dB to
+18 dB.
To use the same volume level as when the AV controller
was last turned off, select “Last”.
was last turned off, select “Last”.
OSD Setup
■ Immediate Display
This setting determines whether operation details are
displayed onscreen immediately after an AV controller
function is used.
This setting determines whether operation details are
displayed onscreen immediately after an AV controller
function is used.
On: Displayed (default).
Off: Not displayed.
Even when “On” is selected, operation details may not
be output if the input source is connected to a COMPO-
NENT VIDEO IN or HDMI IN.
For optimal video performance, THX recommends that
“Immediate Display” be turned off.
be output if the input source is connected to a COMPO-
NENT VIDEO IN or HDMI IN.
For optimal video performance, THX recommends that
“Immediate Display” be turned off.
■ Monitor Type
With this setting, you can specify the aspect ratio of your
TV so that menus are displayed properly.
With this setting, you can specify the aspect ratio of your
TV so that menus are displayed properly.
4:3: Select if your TV is 4:3.
16:9: Select if your TV is 16:9 (default).
■ Display Position
This setting determines where on the screen operation
details are displayed.
This setting determines where on the screen operation
details are displayed.
Bottom: Bottom of the screen (default).
Top: Top of the screen.
■ TV Format (not North American models)
See “TV Format Setup (not North American models)”
on page 56.
See “TV Format Setup (not North American models)”
on page 56.
■ Language
This setting determines the language used for the
onscreen setup menus. You can select: English, German,
French, Spanish, Italian, Dutch, Swedish, or Japanese.
This setting determines the language used for the
onscreen setup menus. You can select: English, German,
French, Spanish, Italian, Dutch, Swedish, or Japanese.
12V Trigger A/B/C Setup