Integra DHC-9.9 Manual De Usuario
126
Tuner
■ AM Freq Step (on some models)
See “AM Frequency Step Setup (on some models)” on
page 57.
See “AM Frequency Step Setup (on some models)” on
page 57.
■ Satellite Radio (on North American model)
If you connect an XM Satellite Radio antenna or SIRIUS
Satellite Radio antenna to the AV controller (both sold
separately), set this setting to XM or SIRIUS respec-
tively. If you connect both types of antenna, select
XM/SIRIUS. Otherwise, select None (see pages 74–88).
If you connect an XM Satellite Radio antenna or SIRIUS
Satellite Radio antenna to the AV controller (both sold
separately), set this setting to XM or SIRIUS respec-
tively. If you connect both types of antenna, select
XM/SIRIUS. Otherwise, select None (see pages 74–88).
Analog Multich
■ Subwoofer Input Sensitivity
Some DVD players output the LFE channel from their
analog subwoofer output at 15 dB higher than normal.
With this setting, you can change the AV controller’s
subwoofer sensitivity to match your DVD player. Note
that this setting only affects signals connected to the AV
controller’s MULTI CH: SUBWOOFER jack.
Some DVD players output the LFE channel from their
analog subwoofer output at 15 dB higher than normal.
With this setting, you can change the AV controller’s
subwoofer sensitivity to match your DVD player. Note
that this setting only affects signals connected to the AV
controller’s MULTI CH: SUBWOOFER jack.
You can select 0 dB, 5 dB, 10 dB, or 15 dB.
If you find that your subwoofer is too loud, try the 10 dB
or 15 dB setting.
or 15 dB setting.
HDMI
■ Audio TV Out
This setting determines whether audio received by an
HDMI input is output by the HDMI outputs. You may
want to change this setting to “On” if your TV is con-
nected to an HDMI output and you want to listen to
audio from an HDMI component through your TV’s
speakers. Normally, it should be set to “Off”.
This setting determines whether audio received by an
HDMI input is output by the HDMI outputs. You may
want to change this setting to “On” if your TV is con-
nected to an HDMI output and you want to listen to
audio from an HDMI component through your TV’s
speakers. Normally, it should be set to “Off”.
Off: HDMI audio is not output (default).
On: HDMI audio is output.
Notes:
• If “On” is selected and the signal can be output by the
• If “On” is selected and the signal can be output by the
TV, the AV controller will output no sound through its
speakers.
speakers.
• When “TV Control” is enabled, this setting is set to
“Auto”.
• With some TVs and input signals, no sound may be
output even if “On” is selected.
• When the “Audio TV Out” setting is set to “On”, or
“TV Control” is set to “Enable” and you’re listening
through your TV’s speakers (see page 38), if you turn
up the AV controller’s volume control, the sound will
be output by the AV controller’s speakers. To stop the
AV controller’s speakers producing sound, change the
settings, change your TV’s settings, or turn down the
AV controller’s volume.
through your TV’s speakers (see page 38), if you turn
up the AV controller’s volume control, the sound will
be output by the AV controller’s speakers. To stop the
AV controller’s speakers producing sound, change the
settings, change your TV’s settings, or turn down the
AV controller’s volume.
■ Lip Sync
The Lip Sync function can automatically synchronize
HDMI audio and video that’s gotten out of sync due to
the complex digital video processing being performed by
your HDMI-compatible TV. With HDMI Lip Sync, the
audio delay required to synchronize the audio and video
is calculated and applied automatically by the AV con-
troller.
The Lip Sync function can automatically synchronize
HDMI audio and video that’s gotten out of sync due to
the complex digital video processing being performed by
your HDMI-compatible TV. With HDMI Lip Sync, the
audio delay required to synchronize the audio and video
is calculated and applied automatically by the AV con-
troller.
Disable: HDMI lip sync disabled (default).
Enable: HDMI lip sync enabled.
Notes:
• This function works only if your HDMI-compatible
• This function works only if your HDMI-compatible
TV supports HDMI Lip Sync.
• You can check the amount of delay being applied by
the HDMI Lip Sync function on the “A/V Sync”
screen (see page 118).
screen (see page 118).
■ x.v.Color
If your HDMI source and HDMI-compatible TV both
support the “x.v.Color”, you can enable “x.v.Color” on
the AV controller with this setting.
If your HDMI source and HDMI-compatible TV both
support the “x.v.Color”, you can enable “x.v.Color” on
the AV controller with this setting.
Disable: “x.v.Color” disabled (default).
Enable: “x.v.Color” enabled.
Notes:
• If the color is unnatural when “x.v.Color” is set to
• If the color is unnatural when “x.v.Color” is set to
“Enable”, change the setting to “Disable”.
• Refer to the connected component’s instruction man-
ual for details.
■ Control
This function allows
This function allows
-compatible components
connected via HDMI to be controlled with the AV con-
troller.
troller.
Notes:
•
•
, which stands for Remote Interactive over
HDMI, is the name of the system control function
found on Onkyo components. The AV controller can
be used with CEC (Consumer Electronics Control),
which allows system control over HDMI and is part of
the HDMI standard. CEC provides interoperability
between various components, however, operation with
components other than
found on Onkyo components. The AV controller can
be used with CEC (Consumer Electronics Control),
which allows system control over HDMI and is part of
the HDMI standard. CEC provides interoperability
between various components, however, operation with
components other than
-compatible compo-
nents cannot be guaranteed.
• Set to “Disable” when a connected piece of equipment
is not compatible or it is unclear whether the equip-
ment is compatible or not.
ment is compatible or not.
• If movement is unnatural when set to “Enable”, change
the setting to “Disable”.
• Refer to the connected component’s instruction man-
ual for details.
Disable:
disabled (default).
Enable:
enabled.