Jonsered CS 2171WH Manual De Usuario
English
– 25
FUEL HANDLING
Fuel
CAUTION! The machine is equipped with a two-stroke engine
and must always been run using a mixture of petrol and two-
stroke engine oil. It is important to accurately measure the
amount of oil to be mixed to ensure that the correct mixture is
obtained. When mixing small amounts of fuel, even small
inaccuracies can drastically affect the ratio of the mixture.
and must always been run using a mixture of petrol and two-
stroke engine oil. It is important to accurately measure the
amount of oil to be mixed to ensure that the correct mixture is
obtained. When mixing small amounts of fuel, even small
inaccuracies can drastically affect the ratio of the mixture.
Petrol
•
Use good quality unleaded or leaded petrol. Engines
equipped with catalytic converters must be run on
unleaded fuel mixtures.
equipped with catalytic converters must be run on
unleaded fuel mixtures.
•
The lowest recommended octane grade is RON 90. If you
run the engine on a lower octane grade than RON 90 so-
called knocking can occur. This gives rise to a high engine
temperature and increased bearing load, which can result
in serious engine damage.
run the engine on a lower octane grade than RON 90 so-
called knocking can occur. This gives rise to a high engine
temperature and increased bearing load, which can result
in serious engine damage.
•
When working with continuous high revs (e.g. limbing) a
higher octane is recommended.
higher octane is recommended.
Environment fuel
JONSERED recommends the use of alkylate fuel, either
Aspen two-stroke fuel or environment fuel for four-stroke
engines blended with two-stroke oil as set out below. Note
that carburettor adjustment may be necessary when
changing the type of fuel (see the instructions under the
heading Carburettor).
Aspen two-stroke fuel or environment fuel for four-stroke
engines blended with two-stroke oil as set out below. Note
that carburettor adjustment may be necessary when
changing the type of fuel (see the instructions under the
heading Carburettor).
Running-in
Avoid running at a too high speed during the first 10 hours.
Two-stroke oil
•
Always use JONSERED two-stroke oil, which is specially
adapted for our two-stroke engines.
adapted for our two-stroke engines.
•
JONSERED provides two stroke oils adapted for different
application areas and climates. Please contact your
dealer for information about the best options for your
product and area of application.
application areas and climates. Please contact your
dealer for information about the best options for your
product and area of application.
•
Never use two-stroke oil intended for water-cooled
outboard engines, sometimes referred to as outboard oil.
outboard engines, sometimes referred to as outboard oil.
•
Never use oil intended for four-stroke engines.
Mixing ratio
For engines up to 80 cc: 01:50 (2%)
For engines over 80 cc: 01:33 (3%)
Mixing
•
Always mix the petrol and oil in a clean container intended
for fuel.
for fuel.
•
Always start by filling half the amount of the petrol to be
used. Then add the entire amount of oil. Mix (shake) the
fuel mixture. Add the remaining amount of petrol.
used. Then add the entire amount of oil. Mix (shake) the
fuel mixture. Add the remaining amount of petrol.
•
Mix (shake) the fuel mixture thoroughly before filling the
machine’s fuel tank.
machine’s fuel tank.
•
Do not mix more than one month’s supply of fuel at a time.
•
If the machine is not used for some time the fuel tank
should be emptied and cleaned.
should be emptied and cleaned.
!
WARNING! Always ensure there is adequate
ventilation when handling fuel.
ventilation when handling fuel.
Petrol, litre
Two-stroke oil, litre
2% (1:50)
3% (1:33)
5
0,10
0,15
10
0,20
0,30
15
0,30
0,45
20
0,40
0,60