Guardian Technologies 004988-4 Manual De Usuario
4
1.1 GENERATOR
This equipment is a liquid-cooled, engine-driven
generator set. The generator is designed to supply
electrical power that operates critical electrical loads
during utility power failure. The unit has been facto-
ry-installed in a weather resistant, all metal enclosure
and is intended for outdoor installation only. Use
this generator as a source of electrical power for the
operation of 120 and/or 240VAC, single-phase loads.
generator set. The generator is designed to supply
electrical power that operates critical electrical loads
during utility power failure. The unit has been facto-
ry-installed in a weather resistant, all metal enclosure
and is intended for outdoor installation only. Use
this generator as a source of electrical power for the
operation of 120 and/or 240VAC, single-phase loads.
If this generator is used to power electrical load
circuits normally powered by a UTILITY power
source, it is required by code to install a trans-
fer switch. The transfer switch must effectively
isolate the electric system from the utility distri-
bution system when the generator is operating
(NEC 701). Failure to isolate an electrical system
by such means results in damage to the genera-
tor and may also result in injury or even death
to utility power workers due to backfeed of
electrical energy.
source, it is required by code to install a trans-
fer switch. The transfer switch must effectively
isolate the electric system from the utility distri-
bution system when the generator is operating
(NEC 701). Failure to isolate an electrical system
by such means results in damage to the genera-
tor and may also result in injury or even death
to utility power workers due to backfeed of
electrical energy.
1.2 TRANSFER
SWITCH
This generator system may include a matched auto-
matic transfer switch which is intended to be used
in conjunction with the generator. It is supplied in
a NEMA 3R enclosure. The NEMA 3R enclosure is
weather proof and can be used indoors or outdoors.
Follow these rules:
matic transfer switch which is intended to be used
in conjunction with the generator. It is supplied in
a NEMA 3R enclosure. The NEMA 3R enclosure is
weather proof and can be used indoors or outdoors.
Follow these rules:
• Install the transfer switch on a firm, sturdy sup-
porting structure.
• To prevent switch distortion, level the switch if
necessary. This can be done by placing washers
between the switch enclosure and the mounting
surface.
between the switch enclosure and the mounting
surface.
• Never install the switch where water or any corro-
sive substance might drip onto the enclosure.
• Protect the switch at all times against excessive
moisture, dust, dirt, lint, construction grit and cor-
rosive vapors.
rosive vapors.
If a transfer switch is not included, one may be pur-
chased separately from an Authorized Dealer.
chased separately from an Authorized Dealer.
1.3 AUTOMATIC
SYSTEM OPERATION
When this generator, along with a transfer switch, has
been installed and interconnected, a circuit board
in the generator panel constantly monitors UTILITY
power source voltage. Should that voltage drop below
a preset value, and remain at such a low state for
a preset amount of time, the generator cranks and
starts. After the generator starts, the transfer switch
transfers load circuits so the generator can power
them.
been installed and interconnected, a circuit board
in the generator panel constantly monitors UTILITY
power source voltage. Should that voltage drop below
a preset value, and remain at such a low state for
a preset amount of time, the generator cranks and
starts. After the generator starts, the transfer switch
transfers load circuits so the generator can power
them.
When UTILITY source voltage has been restored, the
switch re-transfers back to the UTILITY source volt-
age and the generator then shuts down.
switch re-transfers back to the UTILITY source volt-
age and the generator then shuts down.
Please reference the transfer switch manual for spe-
cific information.
cific information.
1.4
GENERATOR AC CONNECTION
SYSTEMS
SYSTEMS
The generator was shipped from the factory with its
stator AC output leads connected in a single-phase,
three-wire generator AC connection system (Figure
1.1). The stator assembly in this system consists of
a pair of stationary windings, with two leads brought
out of each winding. Each single winding can sup-
ply 120VAC, 60 Hertz. When the two windings are
connected in series, a 240VAC, 60 Hertz AC output
results. Typically the two HOT leads in the circuit
are wires 11 and 44. The NEUTRAL leads are the
junction of Wires 22 and 33. The NEUTRAL is not
grounded.
stator AC output leads connected in a single-phase,
three-wire generator AC connection system (Figure
1.1). The stator assembly in this system consists of
a pair of stationary windings, with two leads brought
out of each winding. Each single winding can sup-
ply 120VAC, 60 Hertz. When the two windings are
connected in series, a 240VAC, 60 Hertz AC output
results. Typically the two HOT leads in the circuit
are wires 11 and 44. The NEUTRAL leads are the
junction of Wires 22 and 33. The NEUTRAL is not
grounded.
Figure 1.1 - Generator AC Connection System
1.5 MAIN CIRCUIT BREAKER
The generator’s main circuit breaker is included with
the unit as shipped from the factory. The breaker for
each unit is described in Figure 1.2.
the unit as shipped from the factory. The breaker for
each unit is described in Figure 1.2.
Section 1 - General Information
Liquid-cooled 30 kW Generators
Model
Rating
Phase
Actual
Current
C/B
Rating*
Circuit
Breaker
004988-4
27,000
NG
1
112.5
150
150A
QN2
30,000 LP
1
125.0
150
150A QN2
* Amp Rating of C/B structured under model.
Figure 1.2 - Main Circuit Breaker