Yamaha 01V96i Manual De Usuario
Setting the Stereo Out and Bus Out 1–8 from the Control Surface
33
01V96i—Reference Manual
Bus
Outs
Setting the Stereo Out
and Bus Out 1–8 from the
Control Surface
and Bus Out 1–8 from the
Control Surface
You can use the faders, [SEL] buttons, and various buttons
and controls in the SELECTED CHANNEL section on the
top panel to directly control certain parameters for the Stereo
Out and Bus Out 1–8.
and controls in the SELECTED CHANNEL section on the
top panel to directly control certain parameters for the Stereo
Out and Bus Out 1–8.
Setting the Levels
Move the [STEREO] fader to adjust the Stereo Out levels.
Press the [ON] button in the STEREO section to turn the Ste-
reo Out on or off.
To set Bus Out 1–8 levels, press the [MASTER] button in the
LAYER section to select the Master layer, then move faders
9–16. At this time, you can turn Bus Out 1–8 on or off using
the [ON] 9–16 buttons.
Press the [ON] button in the STEREO section to turn the Ste-
reo Out on or off.
To set Bus Out 1–8 levels, press the [MASTER] button in the
LAYER section to select the Master layer, then move faders
9–16. At this time, you can turn Bus Out 1–8 on or off using
the [ON] 9–16 buttons.
EQ’ing and Balancing the Stereo
Out and Bus Outs
Out and Bus Outs
1.
Press the [SEL] button of the bus to which you
want to apply EQ or set the level balance.
want to apply EQ or set the level balance.
2.
To adjust the EQ of the currently-selected bus,
select the desired band by pressing one of the
following buttons in the SELECTED CHANNEL
section:
select the desired band by pressing one of the
following buttons in the SELECTED CHANNEL
section:
• [HIGH] button...... HIGH band
• [H-MID] button ... HIGH-MID band
• [L-MID] button .... LOW-MID band
• [LOW] button ....... LOW band
• [H-MID] button ... HIGH-MID band
• [L-MID] button .... LOW-MID band
• [LOW] button ....... LOW band
3.
Use the [Q], [FREQUENCY], and [GAIN] con-
trols to adjust the Q, frequency, and gain of
the band selected in Step 2.
trols to adjust the Q, frequency, and gain of
the band selected in Step 2.
See page 21 for more information on EQ.
4.
To adjust the Stereo Out Balance parameter,
use the [PAN] control in the SELECTED CHAN-
NEL section.
use the [PAN] control in the SELECTED CHAN-
NEL section.
Pairing Buses or Aux
Sends
Sends
You can pair adjacent odd-even (in this order) buses or Aux
Sends for stereo operation. Paired bus and Aux Send linked
parameters and non-linked parameters (that are available for
independent controls) are listed below:
Sends for stereo operation. Paired bus and Aux Send linked
parameters and non-linked parameters (that are available for
independent controls) are listed below:
** You can set this parameter for each channel indepen-
dently if the GANG button is turned off on the
/INS/DLY | DLY page.
*** You can set this parameter for each channel indepen-
dently on the EQ | ATT page, but the paired channel set-
tings are linked on the EQ | Edit and View pages.
tings are linked on the EQ | Edit and View pages.
Parameters marked with an asterisk * are available only for
Bus Out 1–8.
Bus Out 1–8.
1.
Press the DISPLAY ACCESS [PAIR/GROUP]
button repeatedly until the Pair/Grup | Out-
put page appears.
button repeatedly until the Pair/Grup | Out-
put page appears.
The parameters on this page are described below.
1
STEREO/MONOx2
These buttons turn Bus or Aux Send pairs on or off.
These buttons turn Bus or Aux Send pairs on or off.
Note:
If you select Aux Out 1–8 or Bus Out 1–8, the [PAN] control
is disabled.
Linked parameters
Non-linked parameters
[SEL] buttons
Output Patching
Fader
Insert Patching
Channel on/off
Delay on/off
Insert on/off
Delay time
**
Solo on/off
Bus to Stereo Pan
*
Comp settings
Attenuators
***
Comp insert position
EQ settings
Fader group
Mute group
Fade time
Recall safe
Bus to Stereo on/off
*
Bus to Stereo fader
*
1
2