ATTO Technology 2500C Manual De Usuario
42
CLI
SNTP
Controls the SNTP (Simple Network Time Protocol)
settings for the iPBridge. When enabled, the iPBridge
tries to contact a specified SNTP server at reset and every
12 hours after to initialize/synchronize the time.
Controls the SNTP (Simple Network Time Protocol)
settings for the iPBridge. When enabled, the iPBridge
tries to contact a specified SNTP server at reset and every
12 hours after to initialize/synchronize the time.
Default: Enabled
Set syntax: set SNTP [enabled|disabled]
Requires a SaveConfiguration command
Get syntax: get SNTP
Set syntax: set SNTP [enabled|disabled]
Requires a SaveConfiguration command
Get syntax: get SNTP
SNTPServer
Controls the IP address of the SNTP time server that the
iPBridge contacts to initialize/synchronize the time.
If the iPBridge is unable to contact the specified SNTP
server within 30 seconds, the iPBridge tries to contact the
first auxiliary SNTP time server. If the first auxiliary
SNTP time server is not available, the iPBridge tries to
contact the second auxiliary SNTP time server. If the
second auxiliary SNTP time server is not available, the
iPBridge continues to approximate the time based on the
most recent SNTP time server, physical real time clock or
manual initialization/synchronization.
Controls the IP address of the SNTP time server that the
iPBridge contacts to initialize/synchronize the time.
If the iPBridge is unable to contact the specified SNTP
server within 30 seconds, the iPBridge tries to contact the
first auxiliary SNTP time server. If the first auxiliary
SNTP time server is not available, the iPBridge tries to
contact the second auxiliary SNTP time server. If the
second auxiliary SNTP time server is not available, the
iPBridge continues to approximate the time based on the
most recent SNTP time server, physical real time clock or
manual initialization/synchronization.
Auxiliary time servers
129.6.15.28 (
www.time-a.nist.gov
)
132.163.4.101 (
www.time-a-timefreq.bidrdoc.gov
)
Default: 192.43.244.18 (
www.time.nist.gov
)
Set syntax: set SNTPServer [xxx.xxx.xxx.xxx]
Requires a SaveConfiguration command
Get syntax: get SNTPServer
Requires a SaveConfiguration command
Get syntax: get SNTPServer
SpeedWrite
When enabled, improves the performance of FCP WRITE
commands to SCSI devices attached to the iPBridge.
Specify SCSI bus (sb), target (st), LUN (sl) of a mapped
SCSI device or (all) for each currently mapped device.
When enabled, improves the performance of FCP WRITE
commands to SCSI devices attached to the iPBridge.
Specify SCSI bus (sb), target (st), LUN (sl) of a mapped
SCSI device or (all) for each currently mapped device.
Set syntax: set SpeedWrite scsi [sb st sl | all] [enabled |
disabled]
Get syntax: get SpeedWrite scsi [sb st sl | all ]
disabled]
Get syntax: get SpeedWrite scsi [sb st sl | all ]
SpeedWriteDefault
When enabled, SpeedWrite performance enhancement is
set as the default for any subsequent SCSI devices
mapped manually or via an AutoMap operation. If
disabled, the iPBridge does not attempt SpeedWrite
performance enhancement to newly-mapped SCSI
devices.
When enabled, SpeedWrite performance enhancement is
set as the default for any subsequent SCSI devices
mapped manually or via an AutoMap operation. If
disabled, the iPBridge does not attempt SpeedWrite
performance enhancement to newly-mapped SCSI
devices.
Set syntax: set SpeedWriteDefault [enabled | disabled]
Get syntax: get SpeedWriteDefault
Get syntax: get SpeedWriteDefault
Time
Controls the time for the iPBridge if SNTP has been
disabled or is not available.
Controls the time for the iPBridge if SNTP has been
disabled or is not available.
Set syntax: set Time [HH]: [MM]: [SS]
Requires a SaveConfiguration command
Get syntax: get Time
Requires a SaveConfiguration command
Get syntax: get Time
TimeZone
Controls the time zone for the iPBridge if SNTP has been
disabled or is not available. Choices are EST, CST,
MST,
Controls the time zone for the iPBridge if SNTP has been
disabled or is not available. Choices are EST, CST,
MST,
.
PST or numerical offset from GMT in the form of
+/-:HH:MM. When SNTP is enabled, the iPBridge
applies the time zone setting to the time retrieved from a
specified SNTP time server to determine local time.
applies the time zone setting to the time retrieved from a
specified SNTP time server to determine local time.
Default: EST
Set syntax: set TimeZone [ [EST | CST | MST | PST] [+ /
- HH :MM ] ]
Requires a SaveConfiguration command
Get syntax: get TimeZone
Set syntax: set TimeZone [ [EST | CST | MST | PST] [+ /
- HH :MM ] ]
Requires a SaveConfiguration command
Get syntax: get TimeZone
Username
Specifies user name for all telnet, FTP and ExpressNAV
web server sessions.The user name is case insensitive, 1-
32 characters, no spaces.
Specifies user name for all telnet, FTP and ExpressNAV
web server sessions.The user name is case insensitive, 1-
32 characters, no spaces.
Changes to the Admin Level
user name require an Admin Level password.
Default: root
Set syntax: set Username [username]
Requires a SaveConfiguration command
Get syntax: get Username
Set syntax: set Username [username]
Requires a SaveConfiguration command
Get syntax: get Username
Zmodem
Allows transfer of a firmware image to or from the
iPBridge using the ZMODEM file transfer protocol.
Zmodem is available only through the RS232 interface.
Before using Zmodem, ensure all I/O to the iPBridge has
stopped.
Allows transfer of a firmware image to or from the
iPBridge using the ZMODEM file transfer protocol.
Zmodem is available only through the RS232 interface.
Before using Zmodem, ensure all I/O to the iPBridge has
stopped.
CAUTION
CAUTION
After a firmware image is downloaded to
the iPBridge, the image is placed into flash
memory. During this time (about 60
seconds), DO NOT remove power to the
iPBridge or the flash may become
corrupted.
the iPBridge, the image is placed into flash
memory. During this time (about 60
seconds), DO NOT remove power to the
iPBridge or the flash may become
corrupted.
Immediate command: Zmodem [Send filename |
Receive]
Receive]