ATTO Technology 2500C Manual De Usuario
41
ATTO Technology Inc. iPBridge Installation and Operation Manual
7.1.3 Maintenance commands
The CLI commands outlined in this chapter may be used to get information or perform functions which
are used in a variety of situations with the ATTO iPBridge.
are used in a variety of situations with the ATTO iPBridge.
Date
Sets the date for the iPBridge if SNTP has been disabled
or is not available.
Sets the date for the iPBridge if SNTP has been disabled
or is not available.
Set syntax: set Date [MM] / [DD] / [YYYY]
Requires a SaveConfiguration command
Get syntax: get Date
Requires a SaveConfiguration command
Get syntax: get Date
FirmwareRestart
Causes the iPBridge to reboot, then re-initialize its
firmware.
Causes the iPBridge to reboot, then re-initialize its
firmware.
Immediate command: FirmwareRestart
MaxOpTemp
Establishes/reports the maximum enclosure temperature
alarm in degrees Celsius. If the temperature of the
iPBridge rises above the maximum MaxOpTemp, thermal
control event handling occurs.
Valid entries are between 55 and 70 degrees C
Establishes/reports the maximum enclosure temperature
alarm in degrees Celsius. If the temperature of the
iPBridge rises above the maximum MaxOpTemp, thermal
control event handling occurs.
Valid entries are between 55 and 70 degrees C
Default: 70
Set syntax: set MaxOpTemp [55-70]
Requires a SaveConfiguration command
Get syntax: get MaxOpTemp
Set syntax: set MaxOpTemp [55-70]
Requires a SaveConfiguration command
Get syntax: get MaxOpTemp
MinOpTemp
Establishes/reports the minimum enclosure temperature
alarm in degrees Celsius. If the temperature of the
iPBridge falls below the minimum MinOpTemp, thermal
control event handling occurs. Valid entries are between
0 and 15 degrees.
Establishes/reports the minimum enclosure temperature
alarm in degrees Celsius. If the temperature of the
iPBridge falls below the minimum MinOpTemp, thermal
control event handling occurs. Valid entries are between
0 and 15 degrees.
Default: 0
Set syntax: set MinOpTemp [0-15]
Requires a SaveConfiguration command
Get syntax: get MinOpTemp
Set syntax: set MinOpTemp [0-15]
Requires a SaveConfiguration command
Get syntax: get MinOpTemp
OpTempWarn
Controls the number of degrees in Celsius before a
thermal control event handling occurs. Warnings are
made via system log entries. Valid entries are between 0
and 15 degrees.
Controls the number of degrees in Celsius before a
thermal control event handling occurs. Warnings are
made via system log entries. Valid entries are between 0
and 15 degrees.
Default: 5
Set syntax: set OpTempWarn [0-15]
Requires a SaveConfiguration command
Get syntax: get OpTempWarn
Set syntax: set OpTempWarn [0-15]
Requires a SaveConfiguration command
Get syntax: get OpTempWarn
Password
Specifies a password for all sessions: NDMP, telnet,
FTP and ExpressNAV web-based interface. A
prompt asks for the current password, to enter the
new password, and to confirm the new password.
Passwords are case sensitive, 0-32 characters with
no spaces. An empty password can be configured by
entering the Password confirmation prompts with no
parameters. The command RestoreConfiguration
default sets the password to its default value.
FTP and ExpressNAV web-based interface. A
prompt asks for the current password, to enter the
new password, and to confirm the new password.
Passwords are case sensitive, 0-32 characters with
no spaces. An empty password can be configured by
entering the Password confirmation prompts with no
parameters. The command RestoreConfiguration
default sets the password to its default value.
Default: Password
Set syntax: set Password
Requires a SaveConfiguration command
Set syntax: set Password
Requires a SaveConfiguration command
Reserve
Reservation of the iPBridge is implicit: once the
configuration image is changed by any user of services,
the iPBridge becomes RESERVED. Executing a
SaveConfiguration or RestoreConfiguration
RELEASES the iPBridge so that other services users may
access it. When iPBridge services interface is
RESERVED, set commands from other users are
unavailable.
At least one interface must always have access to the
iPBridge.
Reservation of the iPBridge is implicit: once the
configuration image is changed by any user of services,
the iPBridge becomes RESERVED. Executing a
SaveConfiguration or RestoreConfiguration
RELEASES the iPBridge so that other services users may
access it. When iPBridge services interface is
RESERVED, set commands from other users are
unavailable.
At least one interface must always have access to the
iPBridge.
Immediate command: Reserve
RestoreConfiguration
Restores configuration to either the default configuration
or the configuration last saved into non-volatile memory.
The saved option undoes any changes made since the last
save.
Restores configuration to either the default configuration
or the configuration last saved into non-volatile memory.
The saved option undoes any changes made since the last
save.
Immediate command: RestoreConfiguration [Default |
Saved]
Saved]
SCSIPortReset
Resets the specified SCSI bus.
Resets the specified SCSI bus.
Immediate command: SCSIPortReset [sb]