Samsung CLP775ND Manual De Usuario

Network setup_ 39

IPv6 is supported properly only in Windows Vista or higher.

1. Connect your machine to the network with a network cable.
2. Turned on the machine.
3. Press 

 on the control panel.

4. Press up/down arrow to highlight Network and press OK.
5. Press up/down arrow to highlight TCP/IP (IPv6) and press OK.
6. Press up/down arrow to highlight IPv6 Activate and press OK.
7. Press up/down arrow to highlight On and press OK.
8. Turn the machine off and turn it on again.
9. Print a Network Configuration Report from the machine’s control 

panel that will check IPv6 addresses.

1.

Press 

 on the control panel.

2.

Press up/down arrow to highlight Network and press OK.

3.

Press up/down arrow to highlight Network Configuration and 

press OK.

In the IPv6 network environment, follow the next procedure to use the IPv6 

address.
1. Connect your machine to the network with a network cable.
2. Turn on the machine.
3. Print a Network Configuration Report that will check IPv6 addresses.
4. Select Start > Control Panel > Printers and Faxes.
5. Click Add a printer in the left pane of the Printers and Faxes windows.
6. Click Add a network, wireless or Bluetooth printer in the Add Printer 

windows.

7. The Add Printer Wizard window appears. Follow the instructions in the 

window.

If the machine does not work in the network environment, activate 

IPv6.

The machine supports the following IPv6 addresses for network printing and 

managements.

•

Link-local Address: Self-configured local IPv6 address (Address starts 

with FE80).

•

Stateless Address: Automatically configured IPv6 address by a 

network router.

•

Stateful Address: IPv6 address configured by a DHCPv6 server.

•

Manual Address: Manually configured IPv6 address by a user.

If you have a DHCPv6 server on your network, you can set one of the 

following options for default dynamic host configuration.

1. Press 

 on the control panel.

2. Press up/down arrow to highlight Network and press OK.
3. Press up/down arrow to highlight TCP/IP (IPv6) and press OK.
4. Press up/down arrow to highlight DHCPv6 Config and press OK.
5. Press up/down arrow to access the required value.

•

Routers: Use DHCPv6 only when requested by a router.

•

DHCPv6 Addresses: Always use DHCPv6 regardless of router 

request.

•

DHCPv6 Off: Never use DHCPv6 regardless of router request.

6. Press OK.

1. Start a web browser such as Internet Explorer that supports IPv6 

addressing as a URL (See "Connecting SyncThru™ Web Service" 

For IPv4, enter the IPv4 address (http://xxx.xxx.xxx.xxx) in the 

address field and press the Enter key or click Go.

2. Click Login on the upper right of the SyncThru™ Web Service 

website.
A log-in page appears. 

3. Type in the ID and Password then click Login .

If it’s your first time logging into SyncThru™ Web Service, type in the 

below default ID and password.

•

ID:  admin 

•

Password:  sec00000 

4. When the SyncThru™ Web Service window opens, click Settings 

> Network Settings.

5. Click TCP/IPv6.
6. Enable the Manual Address In the TCP/IPv6 section.

IPv6 Protocol should enable.

7. Select the Address / Prefix and click the Add button, then the router 

prefix will automatically be entered into the address field. 
Enter the rest of address. (ex: 3FFE:10:88:194::AAAA. “A” is the 

hexadecimal 0 through 9, A through F.)

8. Click the Apply button.

1. Start a web browser such as Internet Explorer that supports IPv6 

addressing as a URL .

2. Click Go to access the SyncThru™ Web Service.
3. Click Login on the upper right of the SyncThru™ Web Service website.

A log-in page appears. 

4. Type in the ID and Password then click Login .

If it’s your first time logging into SyncThru™ Web Service, type in the 

below default ID and password.

•

ID:  admin 

•

Password:  sec00000 

5. Select one of the IPv6 addresses (Link-local Address, Stateless 

Address, Stateful Address, Manual Address) from Network 

Configuration Report.

6. Enter the IPv6 addresses. (ex: http://[FE80::215:99FF:FE66:7701]) 

Address must be enclosed in '[]' brackets.