Wilton 15S Manual De Usuario
18
Depth of Cut
The cutting depth scale is a combination
inch/metric scale (Figure 33), with a cutting
range from 0 to 6" (152.4mm). A manual scale is
mounted directly to the front column. The model
15S planer also features a digital scale for
easier, more precise depth readings.
inch/metric scale (Figure 33), with a cutting
range from 0 to 6" (152.4mm). A manual scale is
mounted directly to the front column. The model
15S planer also features a digital scale for
easier, more precise depth readings.
Figure 33
The distance of upward or downward movement
is controlled by the handwheel (Figure 33).
Before moving the table up or down, loosen the
locking handles (Figure 33). After obtaining
proper table position, tighten the locking
handles.
is controlled by the handwheel (Figure 33).
Before moving the table up or down, loosen the
locking handles (Figure 33). After obtaining
proper table position, tighten the locking
handles.
Maximum depth of cut is 3/16". A limiter (Figure
33) on the front of the head casting limits the
depth of cut on full width planing under 1/8".
33) on the front of the head casting limits the
depth of cut on full width planing under 1/8".
The digital scale should be calibrated before
operating the planer. Refer to page 21.
operating the planer. Refer to page 21.
Maintenance
Disconnect machine from
power source before performing any
maintenance.
maintenance.
Periodic or regular inspections are required to
ensure that the machine is in proper adjustment,
that all screws are tight, that belts are in good
condition, that dust has not accumulated in the
electrical enclosures, and that there are no worn
or loose electrical connections.
ensure that the machine is in proper adjustment,
that all screws are tight, that belts are in good
condition, that dust has not accumulated in the
electrical enclosures, and that there are no worn
or loose electrical connections.
Buildup of sawdust and other debris can cause
your machine to plane inaccurately. Periodic
cleaning is not only recommended but
mandatory for accurate planing.
your machine to plane inaccurately. Periodic
cleaning is not only recommended but
mandatory for accurate planing.
Close-fitting parts, such as the cutterhead slot
and gibs, should be cleaned with a cloth or
brush and non-flammable solvent, and freed
from clinging foreign matter.
and gibs, should be cleaned with a cloth or
brush and non-flammable solvent, and freed
from clinging foreign matter.
Remove resin and other accumulations from
feed rollers and table with a soft rag and non-
flammable solvent.
feed rollers and table with a soft rag and non-
flammable solvent.
Periodically check all the chains for proper
tension and adjust accordingly if required.
tension and adjust accordingly if required.
The table should be kept clean and free of rust.
Some users prefer a paste wax on exposed
steel and cast iron surfaces. The wax provides a
layer of protection as well as reducing friction
between lumber and the table, making cuts
faster and smoother. Avoid any wax that
contains silicone or other synthetic ingredients.
These materials can find their way into lumber
and can make staining and finishing difficult.
Some users prefer a paste wax on exposed
steel and cast iron surfaces. The wax provides a
layer of protection as well as reducing friction
between lumber and the table, making cuts
faster and smoother. Avoid any wax that
contains silicone or other synthetic ingredients.
These materials can find their way into lumber
and can make staining and finishing difficult.
Another option is talcum powder applied with a
blackboard eraser rubbed in vigorously once a
week; this will fill casting pores and form a
moisture barrier. This method provides a table
top that is slick and allows rust rings to be easily
wiped from the surface. Important also is the fact
that talcum powder will not stain wood or mar
finishes as some wax pickup does.
blackboard eraser rubbed in vigorously once a
week; this will fill casting pores and form a
moisture barrier. This method provides a table
top that is slick and allows rust rings to be easily
wiped from the surface. Important also is the fact
that talcum powder will not stain wood or mar
finishes as some wax pickup does.
Lubrication
The bearings on the cutterhead are factory
lubricated and sealed for life – no lubrication is
required.
lubricated and sealed for life – no lubrication is
required.
Gearbox Lubricant
The lubricant in the gear box must be replaced
every 2,500 hours. Multi-purpose gear box
lubricant will be suitable.
To replace the lubricant:
1. Remove the drain plug (A, Figure 34) with a
every 2,500 hours. Multi-purpose gear box
lubricant will be suitable.
To replace the lubricant:
1. Remove the drain plug (A, Figure 34) with a
14mm wrench, and remove filler cap (B-
Figure 33). Drain dirty oil thoroughly.
Figure 33). Drain dirty oil thoroughly.
2. Insert and tighten the drain plug (A, Figure
34).
3. Fill with clean lubricant through hole (B,
Figure 34).
4. Install and tighten filler cap (B, Figure 34).
Figure 34