Bunn 41343 Manual De Usuario

Page 16

MUST GRIND INTO 

FUNNEL FIRST 

(COFFEE NAME) 

SETUP COMPLETE 

BEGIN SETUP OF 

(COFFEE NAME) 

QUIT SETUP? 

YES 

USE LEFT SIDE 

ONLY 

INSERT FUNNEL 

WITH NEW NAME 

REVIEW RECIPES?

NO                 YES

(COFFEE NAME)

NO                  YES

3 BATCHES DONE?

NO                 YES

SET NEW RECIPE?

NO                 YES

2 SEC. 

CYCLES THROUGH

THREE SCREENS 

2 SEC. 

FUNNEL 

CONTAINS NAME 

FUNNEL CONTAINS 

NO NAME 

SETUP BREW VOLUMES, BYPASS,  

PULSE BREW, PREINFUSION, DRIPOUT TIME 

SEE SEPARATE DIAGRAMS 

FOR SETUP INSTRUCTIONS 

FUNNEL DETECTED 

P2299-1

  This function allows the operator to set BREW 

TIMES, and DRIP-OUT TIMES for each coffee name 

preset in the grinder's memory.

 

Certain coffee 

NAMES are stored in the Grinder's 

memory. When a particular name of coffee is ground 

into the Smart Funnel, that name and the batch size 

selected are transferred from the grinder to the 

programming chip located in the funnel handle. The 

funnel is then inserted into the brewer's funnel rails 

(left side on DUAL brewers). The sensor coil on the 

brewer reads the information contained in the handle. 

The name of the coffee flavor will then appear on the 

display. This then allows the operator to set the BREW 

TIMES, and DRIP-OUT TIMES  for that particular coffee 

NAME. It also allows the operator to set other brewing 

parameters, such as BREW TEMPERATURE, READY 

TEMPERATURE, BREW LOCKOUTS, etc. Each coffee 

NAME can be set individually to provide optimum 

brewing quality.

NOTE: Before beginning setup, place a server beneath 

the brew funnel (left side on DUAL brewers).

1.  Insert the funnel into the grinder and select a batch 

size to grind. It is not necessary to have coffee 

beans in the hopper(s) in order to program the 

brewer. The coffee name is pre-selected and stored 

in the grinder's memory (for side being ground 

on DUAL brewers).

2.  Press the  GRIND switch. When the grinder stops 

grinding, remove the funnel.

3.  On the brewer, press and hold the upper right 

hidden switch (®) until the display reads UNITS. 

Release the switch, then press switch again until 

display reads SET NEW RECIPE.

4.  Press and release YES. The display should read 

INSERT FUNNEL WITH NEW NAME, then USE LEFT 

SIDE ONLY on DUAL brewers only, and finally, QUIT 

SETUP? These displays will repeatedly cycle.

5.  Insert  the funnel into the rails of the brewer (left 

side on DUAL brewers). The display should read 

the NAME of the coffee that was ground into the 

funnel, along with a NO and YES. If the NAME on 

the display is correct, press YES. 

6.  If, for some reason, the name of the coffee from 

the grinder did not load properly into the funnel, 

or if a grind has not yet been done, the display will 

read MUST GRIND INTO FUNNEL FIRST. It will be 

necessary to grind another batch following steps 

1 and 2.

7.  If the grind is acknowledged by the brewer, the 

display will read BEGIN SETUP OF (COFFEE NAME). 

Then the screen will display BREW OZ. and a batch 

light will be blinking. (Refer to BREW OZ (SETTING 

OR ADJUSTING for description)

BREW OZ.  XX.X

(-)        DONE        (+)

% BYPASS  XX.X

(-)        DONE        (+)

3 BATCHES DONE?

NO                     YES

P2415

DUAL

BREWERS

only

41343 080108