DeLonghi ECAM26455 Manual De Usuario

14

Making drinks with milk automatically
The CAPPUCCINO,  LATTE, FLAT WHITE and HOT MILK buttons 
on the control panel enable these drinks to be prepared 
automatically. 
Proceed as follows:
1.  Fill the milk container and attach it as described above.
2.   Turn the froth adjustment dial on the milk container lid to 

the position corresponding to the required froth. 

3.   Press the button corresponding to the required drink. The 

name of the drink selected is displayed together with a 
progress bar which gradually fills as preparation progres-
ses.

4.   After a few seconds, frothed milk is delivered from the 

milk spout into the cup below. For drinks with coffee, the 
machine automatically makes the coffee after delivering 
the milk.  

 

t

*GEVSJOHEFMJWFSZZPVXBOUUPTUPQQSFQBSBUJPO QSFTTUIF
corresponding button. 

t

"UUIFFOEPGEFMJWFSZ UPJODSFBTFUIFRVBOUJUZPGNJMLPS
coffee in the cup, just press (within 3 seconds) the button 
corresponding to the drink being made. 

t

%P OPU MFBWF UIF NJML DPOUBJOFS PVU PG UIF SFGSJHFSBUPS
for long periods. The warmer the milk (5°C is ideal), the 
poorer the quality of froth produced.  

Cleaning the milk frother with the CLEAN button  
“Press CLEAN “ flashes on the display each time you use a milk 
function.
To eliminate all milk residues, proceed as follows:
1.  Leave the milk container in the machine (you do not need 

to empty it);

2.   Place a cup or other recipient under the frothed milk 

spout.

3.   Press the CLEAN button (fig. 23) and keep pressing until 

the progress bar which appears on the display together 
with the message “Cleaning underway” is complete. 

t

*GZPVBSFNBLJOHBOVNCFSPGNJMLCBTFEESJOLTPOFBGUFS
the other, you do not need to clean by pressing the CLEAN 
button each time you make a cappuccino.  

 

Just press it once after making the last cup (the appliance 
continues functioning even if the CLEAN button is not 
pressed). 

After use, always clean the hot water/steam nozzle and the 
milk container as described on page 14.

MILK buttons.
The appliance is set by default to automatically deliver standard 
quantities. 
To change these quantities, proceed as follows:
1.  Place a cup under the coffee and milk spouts.
2.   Press and hold one of the function buttons until the 

message “Milk for … Program Quantity” is displayed. 

3.   Release the button.  
 

The appliance starts delivering milk.

4.   Once the required quantity of milk has been delivered into 

the cup, press the button again. 

5.   The appliance stops delivering milk and (if required for 

the drink being prepared) after a few seconds the coffee is 
delivered into the cup. “Coffee for … Program Quantity” 
is displayed. 

6.   Once the required quantity of coffee has been delivered 

into the cup, press the button. 

 

Coffee delivery stops.

The machine is now reprogrammed with the new quantities 
of milk and coffee. 

Never leave the machine unsupervised while delivering hot 
water or steam.  
The spout becomes hot during delivery. Hold by the handle 
only. 

If “Energy Saving” mode is enabled, you may have to wait a few 
seconds before the hot water or steam is delivered.

Delivering hot water 
1.  Make sure the hot water spout is attached correctly (fig. 

6). 

2.   Place a container under the spout (as close as possible to 

avoid splashes). 

3. Press 

the 

button (fig. 3). 

 

“Hot water” is displayed, together with a progress bar 
which fills gradually as preparation proceeds. 

4.  The machine delivers 250 ml of hot water, then delivery 

stops automatically.  

 

To interrupt delivery of hot water manually, press the 

 button again. 

Change the quantity of water delivered automatically. 
The machine is set by default to automatically delivery 250 ml 
of hot water.