Cypress CY7C68003 Manual De Usuario
CY7C68003
Page 3 of 5
Clocking
TX2UL supports external crystal and clock inputs at the 13, 19.2,
24, and 26 MHz frequencies. The internal PLL applies the proper
clock multiply option depending on the input frequency. For appli-
cations that use an external clock source to drive XI, the XO pin
(in 24-pin QFN package) is left floating. TX2UL has an on-chip
oscillator circuit that uses an external 13, 19.2, 24, or 26 MHz
(±100 ppm) crystal with the following characteristics:
24, and 26 MHz frequencies. The internal PLL applies the proper
clock multiply option depending on the input frequency. For appli-
cations that use an external clock source to drive XI, the XO pin
(in 24-pin QFN package) is left floating. TX2UL has an on-chip
oscillator circuit that uses an external 13, 19.2, 24, or 26 MHz
(±100 ppm) crystal with the following characteristics:
■
Parallel Resonant
■
Fundamental Mode
■
750 mW Drive Level
■
12 pF (5 percent tolerance) Load Capacitors
■
150 ppm
TX2UL operates on one of two primary clock sources:
■
LVCMOS square wave clock input driven on the XI pin
■
Crystal generated sine wave clock on the XI and XO pins
The selection between input clock source and frequency on the
XI pin is determined by the Chip Configuration register loaded
through the RESET_N during Configuration Mode. The external
clock source requirements are shown in
XI pin is determined by the Chip Configuration register loaded
through the RESET_N during Configuration Mode. The external
clock source requirements are shown in
.
Figure 2. Crystal Configuration
Power Domains
The TX2UL has three power supply domains:
■
VCC
■
VIO
■
VBATT
TX2UL has two grounds:
■
VSS
■
VSSBATT
VCC
This is the core 1.8V power supply for the TX2UL. It can range
anywhere from 1.7V to 1.9V during actual operation.
anywhere from 1.7V to 1.9V during actual operation.
VIO
This is the 1.8V to 3.3V multi range supply to the I/O ring. It can
range anywhere from 1.7V to 3.6V during actual operation.
range anywhere from 1.7V to 3.6V during actual operation.
VBATT
This is the battery input supply that powers the 3.3V Regulator
block. It can range anywhere from 3.0 to 5.775V during actual
operation.
block. It can range anywhere from 3.0 to 5.775V during actual
operation.
Voltage Regulator
The internal 3.3V regulator block regulates the VBATT supply to
the internal 3.3V supply for the USBIO and XOSC blocks. If the
supply voltage at VBATT is below 3.3V, the regulator block
switches the VBATT supply directly for the USBIO and XOSC
blocks.
the internal 3.3V supply for the USBIO and XOSC blocks. If the
supply voltage at VBATT is below 3.3V, the regulator block
switches the VBATT supply directly for the USBIO and XOSC
blocks.
Power Supply Sequence
TX2UL does not require power supply sequence. All power
supplies are independently sequenced without damaging the
part. All supplies are up and stable for the device to function
properly. The analog block contains circuitry that senses the
power supply to determine when all supplies are valid.
supplies are independently sequenced without damaging the
part. All supplies are up and stable for the device to function
properly. The analog block contains circuitry that senses the
power supply to determine when all supplies are valid.
TX2UL
XI
XO
PLL
12 pf
12 pf
XTAL
*
12 pF capacitor values assumes a trace capacitance of
3 pF per side on a four layer FR4 PCA
Table 3. External Clock Requirements
Parameter
Description
Specification
Unit
Min
Max
Vn
Supply Voltage Noise at frequencies < 50 MHz
20
mV p-p
PN_100
Input Phase Noise at 100 Hz
–75
dBc/Hz
PN_1k
Input Phase Noise at 1 kHz offset
–104
dBc/Hz
PN_10k
Input Phase Noise at 10 kHz offset
–120
dBc/Hz
PN_100k
Input Phase Noise at 100 kHz offset
–128
dBc/Hz
PN_1M
Input Phase Noise at 1 MHz offset
–130
dBc/Hz
Duty Cycle
30
70
%
Maximum Frequency Deviation
150
ppm