Pioneer SC-35 Manual De Usuario
Using other functions
09
81
En
Using the sleep timer
The sleep timer switches the receiver into standby after a
specified amount of time so you can fall asleep without
worrying about the receiver being left on all night. Use
the remote control to set the sleep timer.
specified amount of time so you can fall asleep without
worrying about the receiver being left on all night. Use
the remote control to set the sleep timer.
•
Set the remote control to the receiver operation
mode, then press SLEEP repeatedly to set the sleep
time.
time.
• You can check the remaining sleep time at any time
by pressing SLEEP once. Pressing repeatedly will
cycle through the sleep options again.
cycle through the sleep options again.
1
Dimming the display
You can choose between four brightness levels for the
front panel display. Note that when selecting sources, the
display automatically brightens for a few seconds.
front panel display. Note that when selecting sources, the
display automatically brightens for a few seconds.
•
Set the remote control to the receiver operation
mode, then press DIMMER repeatedly to change the
brightness of the front panel display.
brightness of the front panel display.
Switching the HDMI output
Set which terminal to use when outputting video and
audio signals from the HDMI output terminals.
audio signals from the HDMI output terminals.
The HDMI OUT1 terminal is compatible with the Control
with HDMI function.
with HDMI function.
•
Set the remote control to the receiver operation
mode, then press HDMI OUT.
Please wait a while when Please wait ... is displayed.
Please wait a while when Please wait ... is displayed.
The output switches among HDMI OUT ALL, HDMI OUT
1 and HDMI OUT 2 each time the button is pressed.
1 and HDMI OUT 2 each time the button is pressed.
2
Using the Web Control function
The receiver can be operated using a browser from a
computer connected on the same LAN as the receiver.
computer connected on the same LAN as the receiver.
1
Turn on the computer and launch the Internet
browser.
2
In the address bar on the browser, enter the IP
address assigned to this receiver.
For example, if the IP address of this receiver is
“192.168.0.2”, enter “http://192.168.0.2/”.
For example, if the IP address of this receiver is
“192.168.0.2”, enter “http://192.168.0.2/”.
When the connection is made with the receiver, a Top
Menu will be displayed.
Menu will be displayed.
This receiver’s IP address can be found in the ‘IP address,
Proxy’ menu (page 117).
Proxy’ menu (page 117).
3
Once the Top Menu is displayed, click the button for
the zone you want to operate.
4
Operate from the screen for the individual zone.
• Even when the receiver is in the standby mode, it can
be turned on using the Web Control function. For
details, see Network Standby on page 118.
details, see Network Standby on page 118.
Checking your system settings
Use the status display screen to check your current
settings for features such as surround back channel
processing and your current MCACC preset.
settings for features such as surround back channel
processing and your current MCACC preset.
1
Set the remote control to the receiver operation
mode, then press STATUS to check the system settings.
The front panel display shows each of the following
settings for three seconds each: Input function,
Sampling Frequency, MCACC preset, ZONE 2 input,
ZONE 3 input and HDMI OUT.
The front panel display shows each of the following
settings for three seconds each: Input function,
Sampling Frequency, MCACC preset, ZONE 2 input,
ZONE 3 input and HDMI OUT.
2
When you’re finished, press STATUS again to
switch off the display.
Note
1 The sleep timer is valid for all zones. If any zone is on, the sleep timer continues functioning.
2 • The synchronized amp mode is canceled when the HDMI output is switched. If you wish to use the synchronized amp mode, switch to HDMI
2 • The synchronized amp mode is canceled when the HDMI output is switched. If you wish to use the synchronized amp mode, switch to HDMI
OUT 1, then select the synchronized amp mode on the TV using the TV’s remote control.
• When the power is turned off then back on after switching the HDMI output, the input is set to a setting between HDMI1 and HDMI3, or BD.
• When the power is turned off then back on after switching the HDMI output, the input is set to a setting between HDMI1 and HDMI3, or BD.
30 min
60 min
90 min
Off
Web Control
ZONE 2
POWER
INPUT SELECT
LISTENING MODE
STEREO
AUTO SURR/ALC/
STREAM DIRECT
STREAM DIRECT
HOME
THX
STANDARD
SURROUND
SURROUND
ADVANCED
SURROUND
SURROUND
STEREO
DVD
VOLUME
MUTE
-60.0dB
ON
OFF
Top Menu
Main ZONE
ZONE 3
SC-37_35_UXJCB.book 81 ページ ２０１０年３月９日 火曜日 午前９時３２分