Polycom 3725-74600-004 Manual De Usuario
Chapter 20-System Configuration Flags
Polycom, Inc.
20-13
802_FIPS_MODE
Not supported with RealPresence Collaboration Server Virtual
Edition.
Edition.
ACCEPT_VOIP_DTMF_TYP
E
E
Defines the type of DTMF tones (inband) or digits (outband)
that the Collaboration Server will accept in VOIP calls.
Range:
that the Collaboration Server will accept in VOIP calls.
Range:
•
0 - Auto (default):
Inband or outband DTMF tones/digits are accepted
depending on the endpoint's current setting. If the
endpoint switches from inband to outband or visa versa
the value of the SET_DTMF_SOURCE_DIFF_IN_SEC
flag determines the time interval after which both inband
and outband tones/digits will be accepted.
Inband or outband DTMF tones/digits are accepted
depending on the endpoint's current setting. If the
endpoint switches from inband to outband or visa versa
the value of the SET_DTMF_SOURCE_DIFF_IN_SEC
flag determines the time interval after which both inband
and outband tones/digits will be accepted.
•
1 - Outband (H.245) only
•
2 - Inband only
ANAT_IP_PROTOCOL
If YES, enables Alternative Network Address Types.
Range: DISABLED, AUTO, PREFER_IPv4, PREFER_IPv6
Range: DISABLED, AUTO, PREFER_IPv4, PREFER_IPv6
•
Default: YES
APACHE_KEEP_ALIVE_TIM
EOUT
EOUT
If the connection is idle for longer than the number of seconds
specified by this flag, the connection to the Collaboration
Server is terminated.
Value: 0 - 999
Default: 15
Note: A value of 0 results in an unlimited keep-alive duration.
specified by this flag, the connection to the Collaboration
Server is terminated.
Value: 0 - 999
Default: 15
Note: A value of 0 results in an unlimited keep-alive duration.
AVOID_VIDEO_LOOP_BAC
K_IN_CASCADE
K_IN_CASCADE
When set to YES the current speaker’s image is not sent back
through the participant link in cascaded conferences with
conference layouts other than 1x1.
Default: YES
Range: YES / NO
through the participant link in cascaded conferences with
conference layouts other than 1x1.
Default: YES
Range: YES / NO
BLOCK_CONTENT_LEGAC
Y_FOR_LYNC
Y_FOR_LYNC
This flag is used to control the system behavior in an
environment where some Lync clients use the Polycom CCS
plug-in and some do not.
When set to NO (default), Content is sent to all Lync clients
over the video channel, including those with the plug-in
installed, even when the Send Content to Legacy Endpoints is
disabled. Other, non-Lync legacy endpoints will not be
affected by this flag and will receive content according to the
Send Content to Legacy Endpoints settings in the conference
Profile.
When set to YES, Content is not sent to Lync clients over the
video channel including those with the Polycom CCS plug-in
installed, even when the Send Content to Legacy Endpoints is
enabled. Other, non-Lync legacy endpoints will not be affected
by this flag and will receive content according to the Send
Content to Legacy Endpoints settings in the conference
Profile.
environment where some Lync clients use the Polycom CCS
plug-in and some do not.
When set to NO (default), Content is sent to all Lync clients
over the video channel, including those with the plug-in
installed, even when the Send Content to Legacy Endpoints is
disabled. Other, non-Lync legacy endpoints will not be
affected by this flag and will receive content according to the
Send Content to Legacy Endpoints settings in the conference
Profile.
When set to YES, Content is not sent to Lync clients over the
video channel including those with the Polycom CCS plug-in
installed, even when the Send Content to Legacy Endpoints is
enabled. Other, non-Lync legacy endpoints will not be affected
by this flag and will receive content according to the Send
Content to Legacy Endpoints settings in the conference
Profile.
Table 20-2
Manually Added System Flags – MCMS_PARAMETERS (Continued)
Flag
Description