3com 3C172221 Manual De Usuario
Handling the Module
The Module can be easily damaged by electrostatic
discharge. To prevent damage, observe the following:
discharge. To prevent damage, observe the following:
Always wear an anti-static wristband connected to a
suitable earth point.
suitable earth point.
Do not remove the Module from its packaging until
you are ready to install it into a Switch.
you are ready to install it into a Switch.
Do not touch any of the pins, connections or
components on the Module.
components on the Module.
Handle the Module only by its edges and front panel.
Always store or transport the Module in anti-static
packaging.
packaging.
Installing the Module into a Switch
CAUTION: This Module is not hot-swappable. Always
make sure that the Switch is powered down and
disconnected from the mains before installing or
removing a Module. Use the following instructions when
installing or removing a Module.
make sure that the Switch is powered down and
disconnected from the mains before installing or
removing a Module. Use the following instructions when
installing or removing a Module.
Each Switch has the facility to accept up to two
Expansion Modules, allowing Cascade, Gigabit Ethernet
or Fast Ethernet connections. Modules can be inserted
into either Expansion Module slot.
Expansion Modules, allowing Cascade, Gigabit Ethernet
or Fast Ethernet connections. Modules can be inserted
into either Expansion Module slot.
Figure 1 Inserting the Module into the Switch
To install the Module:
1 Ensure that the Switch is disconnected from the mains
power supply and that you are wearing an anti-static
wristband connected to a suitable earth point.
wristband connected to a suitable earth point.
2 Undo the two screws securing the blanking plate at the
rear of the Switch using a suitable screwdriver. Do not
remove any other screws from the rear of the Switch.
remove any other screws from the rear of the Switch.
3 Remove the blanking plate.
4 Hold the Module so that the text on the front panel is
). Make sure
the Module is pushed fully in.
5 Secure the Module by tightening the two captive screws
with a screwdriver.
6 Keep the blanking plate and screws in a safe place. If you
remove the Module at any time, you must replace the
blanking plate to prevent dust and debris entering the
Switch. Replacing the blanking plate will also help
circulate cool air through the Switch.
blanking plate to prevent dust and debris entering the
Switch. Replacing the blanking plate will also help
circulate cool air through the Switch.
Activating the Module
1 Ensure that the Switch is powered-up.
2 Remove the protective stopper from the MT-RJ fiber
socket on the Module. Squeeze the top and bottom of
the stopper between your thumb and forefinger then
remove it.
the stopper between your thumb and forefinger then
remove it.
3 Plug the MT-RJ connector on the fiber cable into the
MT-RJ fiber socket on the Module.
4 Connect the other end of the fiber optic segment to a
device fitted with a 1000BASE-SX connection.
5 Check the LEDs on the front of the Switch to ensure that
the Module is operating correctly. Refer to
for
more information.
Removing the Module from a Switch
1 Ensure that the power supply and the fiber backbone
connection cables are disconnected from the Switch.
2 Undo the Module’s two captive screws with a suitable
screwdriver. Do not remove any other screws from the
Switch.
Switch.
3 Remove the Module.
4 If you are not fitting another Module immediately, you
must replace the blanking plate to ensure that dust and
debris do not enter the Switch. Replacing the blanking
plate will also help circulate cool air through the Switch.
debris do not enter the Switch. Replacing the blanking
plate will also help circulate cool air through the Switch.
I
NSTALLATION
AND
R
EMOVAL
!
Modul
e 2
MT-RJ
Fiber Socket
Super
Stack 3 1000BASE-
SX M
odul
e
This pr
oduct
com
plies wi
th DHHS Rul
e 21 CFR
Subchapt
er J, appl
icabl
e at dat
e of m
anuf
acture
3Com
Eur
ope Li
mited
This pr
oduct
com
plies wi
th DHHS Rul
e 21 CFR
Subchapt
er J, appl
icabl
e at dat
e of m
anuf
acture
3Com
Eur
ope Li
mited
3C17221
CLASS1 L
ASER PRODUCT
CLASS1 L
ASER PRODUCT
3