Linksys WAG54G Instruccion De Instalación

If your ISP says that you are 

connecting through a dynamic IP 

address (Figure D1), perform these 

steps:

a

Select RFC 1483 Bridged for 

the Encapsulation.

b

Select Obtain an IP Address 

Automatically for the IP Set-

tings.  

c

Click the Save Settings button  

to save the settings. 

If your ISP says that you are 

connecting through a static or fixed 

IP address (Figure D2), perform these 

steps:

a

Select RFC 1483 Bridged for 

the Encapsulation.

b

Select Use the following IP 

Address as the IP Settings.

c

Enter the IP Address and the 

Subnet Mask

d

Enter the Default Gateway 

address.

in lowercase letters in the 

Password field (admin is the 

default user name and 

password.) Then, click the OK 

button. 

C

The Basic Setup screen will 

appear with the Setup tab 

selected. (Figure C) Based on 

the setup instructions from your 

ISP, you may need to provide 

the following information.

Virtual Circuit (VPI and VCI):  

These fields consist of two 

items: VPI (Virtual Path Identifier) 

and VCI (Virtual Channel 

Identifier).  Your ISP will provide 

the correct settings for each 

field.

D

Encapsulation: This Gateway 

supports multiple settings for 

the Encapsulation. The most 

common Encapsulation 

methods are described below. 

All methods are included in the 

User Guide on the CD-ROM.

The settings required will 

depend on the Encapsulation 

chosen here.  Your ISP will 

provide the correct settings.

4

E

If you haven’t already done so, 

click the Save Settings button  

to save your Setup settings. 

Close the web browser.

F

For Wireless Configuration: 

Please see the User Guide for 

detailed instructions on how to 

configure your Gateway for 

your wireless network. Linksys 

recommends changing your 

wireless settings from the 

defaults and enabling the 

appropriate security options.

If you need advanced 

setting information, 

please refer to the 

Linksys support website 

at linksys.com/support 

or the User Guide.

G

Congratulations! You’ve 

successfully configured the 

Gateway. Test the setup by 

opening your web browser 

from any computer and 

entering: 

www.linksys.com/registration

H

If you are unable to reach our 

website, you may want to 

review the installation and 

configuration sections in this 

Quick Installation or refer to the 

Troubleshooting section of the 

User Guide.

e

Enter the DNS in the Primary 

and/or Secondary fields. You 

need to enter at least one DNS 

address.

f

Click the Save Settings button  

to save the settings. 

If your ISP says that you are 

connecting through PPPoE (Figure 

D3) or PPPoA (Figure D4), or if you 

normally enter a user name and 

password to access the Internet, 

perform these steps:

a

Select PPPoE or PPPoA as 

appropriate for the 

Encapsulation.

b

If you selected PPPoE,enter the 

Service Name (if required).

c

Enter the User Name.

d

Enter the Password.

e

Click the Save Settings button  

to save the settings.

Model No.

Quick Installation

WAG54G-QI-31009NC BW

D

1

D

2

D

3

D

4

Dynamic

Static

PPPoE

PPPoA

For additional information or troubleshooting 
help, refer to the User Guide on the Setup 
CD-ROM. You can also call or email for further 
support.

800-326-7114 
(toll-free from US or Canada)

support@linksys.com

http://www.linksys.com   or

http://support.linksys.com

http://www.linksys.com/support

ftp://ftp.linksys.com

800-546-5797 (800-LINKSYS)

Linksys is a registered trademark or trademark of 
Cisco Systems, Inc. and/or its affiliates in the U.S. 
and certain other countries. Copyright © 2003 
Cisco Systems, Inc. All rights reserved.

C