Conairphone cid154 Manual De Propietario
TELEPHONE FEATURES
Tone/Pulse Switch
Set switch to your type of service. If you don’t know whether you
have tone or pulse:
1. Put the switch on TONE.
2. When you have a dial tone, press any key on the keypad. If
have tone or pulse:
1. Put the switch on TONE.
2. When you have a dial tone, press any key on the keypad. If
the dial tone stops, leave it on TONE. If not, change the setting
to PULSE.
to PULSE.
Receiver Volume Control
The receiver volume control is located on the handset of your
phone. This enables you to adjust the receiver volume from
normal (NORM) to high (HI) for a better listening level.
phone. This enables you to adjust the receiver volume from
normal (NORM) to high (HI) for a better listening level.
Ringer Off/Low/High
Your CID154 features a harmonic dual tone ringer that can be
adjusted from a loud (HI) to a soft (LO) sound level. When you
don’t want to be disturbed, slide the switch to the OFF position.
You can still make outgoing calls without being disturbed by
incoming calls.
adjusted from a loud (HI) to a soft (LO) sound level. When you
don’t want to be disturbed, slide the switch to the OFF position.
You can still make outgoing calls without being disturbed by
incoming calls.
Pause
Whether you have Tone or Pulse service, you can insert a 4-
second PAUSE into the dialing or storing of a number into
memory in order to access custom and telebanking services,
long distance, etc. Press [REDIAL] at the desired point in the
number. Press [REDIAL] again if an additional 4 seconds is
needed.
second PAUSE into the dialing or storing of a number into
memory in order to access custom and telebanking services,
long distance, etc. Press [REDIAL] at the desired point in the
number. Press [REDIAL] again if an additional 4 seconds is
needed.
Redial Button
Automatically redials last number called (up to 32 digits). If the
number was busy or unanswered:
1. Lift the handset.
2. Press [REDIAL].
number was busy or unanswered:
1. Lift the handset.
2. Press [REDIAL].
Flash
The FLASH button can be used to obtain a new dial tone after
ending a call. The FLASH button is also a useful feature for
special telephone services such as Call Waiting and Three-Way
Calling.
Note: These special telephone services must be subscribed to
separately from your local phone company.
ending a call. The FLASH button is also a useful feature for
special telephone services such as Call Waiting and Three-Way
Calling.
Note: These special telephone services must be subscribed to
separately from your local phone company.
SETTING UP YOUR CID154
DO NOT CONNECT the line cord to the wall outlet until the
Caller ID setup has been completed.
Caller ID setup has been completed.
The LCD shows ‘ENTER LANGUAGE’
followed by a choice of 3 languages
(English, Spanish, French). If your
display does not appear this way, press and hold both [ ] and
[ ] for 4 seconds.
The LCD then shows ‘ENG ESP FRA’.
NOTE: The ‘ENG’ is blinking. Press [ ]
or [ ] to select ‘ENG’, ‘ESP’, or ‘FRA’.
Press [ERASE] to confirm.
followed by a choice of 3 languages
(English, Spanish, French). If your
display does not appear this way, press and hold both [ ] and
[ ] for 4 seconds.
The LCD then shows ‘ENG ESP FRA’.
NOTE: The ‘ENG’ is blinking. Press [ ]
or [ ] to select ‘ENG’, ‘ESP’, or ‘FRA’.
Press [ERASE] to confirm.
Once ENG is selected, the LCD shows
‘LCD CONTRAST’.
Press [ ] or [ ] to adjust five levels (from
1 to 5, default is 3) contrast of LCD.
Press [ERASE] to confirm.
‘LCD CONTRAST’.
Press [ ] or [ ] to adjust five levels (from
1 to 5, default is 3) contrast of LCD.
Press [ERASE] to confirm.
Once contrast is set, the LCD shows
‘ENTER AREA CODE’. The first digit
‘–’ of the area code will blink.
Press [ ] or [ ] to enter the area code.
Press [ERASE] to confirm and go to next entry.
Repeat above steps until 3-digit area code is set.
‘ENTER AREA CODE’. The first digit
‘–’ of the area code will blink.
Press [ ] or [ ] to enter the area code.
Press [ERASE] to confirm and go to next entry.
Repeat above steps until 3-digit area code is set.
The LCD shows ‘TOTAL:00 NEW:00’,
which means both the total call and new
call counter are zero.
which means both the total call and new
call counter are zero.
CONNECTING THE TELEPHONE
1. Plug one end of the telephone line cord into the TEL. LINE
jack at the rear of the cradle.
2. Plug the other of the telephone line cord into the modular
wall jack.
With a four prong style jack, simply use a plug in modular
adapter.
With a four prong style jack, simply use a plug in modular
adapter.
3. Connect the coil cord to the jack in the handset and the
HANDSET jack at the rear of the cradle. Then put the handset
into the cradle.
into the cradle.
Backlit LCD Display
For better visibility in a dim light, a backlit LCD display is provided
with batteries installed. The backlit LED will light up when lifting
up the handset from the cradle, receiving an incoming call or
pressing any key. It will turn off after 10 seconds when no key is
pressed.
with batteries installed. The backlit LED will light up when lifting
up the handset from the cradle, receiving an incoming call or
pressing any key. It will turn off after 10 seconds when no key is
pressed.
TELEPHONE OPERATION
Receiving a Call
1. When you receive a call, the phone will ring and the LCD will
display the name and telephone number of the caller. If you
want to talk to the caller, pick up the handset and use it like
any basic telephone.
want to talk to the caller, pick up the handset and use it like
any basic telephone.
2. Replace the handset to the cradle to release the telephone
line when your conversation is completed.
Dialing a Call
1. Pick up the phone and wait for a dial tone.
2. Press the keypad for the telephone number you wish to dial.
2. Press the keypad for the telephone number you wish to dial.
The display will show the number that you dialled on the
keypad. If you dial a number over 14 digits long, it will show
the last 14 digits only.
keypad. If you dial a number over 14 digits long, it will show
the last 14 digits only.
Tone/Pulse Combination Dialing
Combination dialing is useful to subscribers of Pulse (rotary)
service who wish to gain access to various low-cost long-
distance or automated computer services otherwise not available
to them.
1. With the TONE/PULSE switch in the PULSE position, dial
service who wish to gain access to various low-cost long-
distance or automated computer services otherwise not available
to them.
1. With the TONE/PULSE switch in the PULSE position, dial
the phone number.
2. Press [ ], and your telephone will change to TONE dialing
mode.
3. Dial your code/authorization number. When your call is
completed, your telephone will automatically return to the
pulse dialing mode.
pulse dialing mode.
NOTE: Combination dialing can also be stored into the memory
for one-touch access to your long distance or automated
computer service.
for one-touch access to your long distance or automated
computer service.
7
8
9