Crown ce-1000 Manual Suplementario
CE Series Service Manual
Rev.D
Neutrik Connectors 4-1
4 Neutrik Connectors
The
CE-Series of amplifiers uses Neutrik Speakon
connectors for the outputs. While the Reference
Manual contains detailed instructions on how to as-
semble these connectors, we thought we would in-
clude the information here as well. This may help in
troubleshooting problems that may have arisen from
incorrect assembly.
Manual contains detailed instructions on how to as-
semble these connectors, we thought we would in-
clude the information here as well. This may help in
troubleshooting problems that may have arisen from
incorrect assembly.
Fig. 4.1
Order of Assembly for the Neutrik Speakon NL4FC Connector
Order of Assembly for the Neutrik Speakon NL4FC Connector
You will need two (2) Neutrik Speakon
®
NL4FC con-
nectors to interface with this amplifier.* You will also
need high-quality two- or four-conductor speaker
cable with the appropriate end-connectors to fit the
inputs on your speakers, a pair of needle-nosed pliers
and a 1.5-mm hex key to assemble the Speakon con-
nectors.
need high-quality two- or four-conductor speaker
cable with the appropriate end-connectors to fit the
inputs on your speakers, a pair of needle-nosed pliers
and a 1.5-mm hex key to assemble the Speakon con-
nectors.
To assemble the Neutrik Speakon NL4FC connector,
complete the following steps:
complete the following steps:
Slide the bushing (E) and chuck (D) onto the end of
the cable as shown (Figure 4.1).**
the cable as shown (Figure 4.1).**
Strip approximately
3
/
4
-inch (19-mm) of casing from
the cable end. Strip approximately
1
/
4
-inch (6-mm)
from the end of each of the conductors down to bare
wire.
wire.
Slide the end sleeves (C) onto the wire ends and
crimp in place.
crimp in place.
* You can purchase the Speakon
®
NL4FC connectors from your local
dealer, or contact NEUTRIK AG, Im alten riet 34, Schaan FL-9494,
Furstentum Liechtenstein, 011-41-75-237-2424, FAX 011-41-75-232-
5393, www.neutrik.com or Neutrik USA, Inc., 195 Lehigh Ave., Lake-
wood, NJ 08701-4527, (908) 901-9488, Fax (908) 901-9608,
www.neutrikusa.com or Crown International, Inc., 1718 West
Mishawaka Road, Elkhart, IN 46517-4095, USA, 219-294-8000, FAX
219-294-8329, www.crownaudio.com.
Furstentum Liechtenstein, 011-41-75-237-2424, FAX 011-41-75-232-
5393, www.neutrik.com or Neutrik USA, Inc., 195 Lehigh Ave., Lake-
wood, NJ 08701-4527, (908) 901-9488, Fax (908) 901-9608,
www.neutrikusa.com or Crown International, Inc., 1718 West
Mishawaka Road, Elkhart, IN 46517-4095, USA, 219-294-8000, FAX
219-294-8329, www.crownaudio.com.
** Your NL4FC connector kit should contain both a black and a white
chuck. Use the white chuck for cable with a diameter of 0.25- to 0.5-
inch (6.35- to 12.7 mm). Use the black chuck for cable with a diameter
of 0.375- to 0.625-inch (9.525- to 15.875-mm).
inch (6.35- to 12.7 mm). Use the black chuck for cable with a diameter
of 0.375- to 0.625-inch (9.525- to 15.875-mm).
Insert each wire with end sleeve into the top of appro-
priate slot of the connector insert (B) as shown in Fig-
ure4.2. Use a 1.5-mm hex key inserted into each side
slot to tighten the connection.
priate slot of the connector insert (B) as shown in Fig-
ure4.2. Use a 1.5-mm hex key inserted into each side
slot to tighten the connection.
If the Mode switch is in the “Stereo” position (for ste-
reo configuration), connect the positive (+) and
negative (–) leads of each wire to the appropriate
Channel 1 and Channel 2 connectors as shown in
Figure 4.3. You may use all 4 poles of the Channel 1
output connector to feed both speakers, if you wish.
reo configuration), connect the positive (+) and
negative (–) leads of each wire to the appropriate
Channel 1 and Channel 2 connectors as shown in
Figure 4.3. You may use all 4 poles of the Channel 1
output connector to feed both speakers, if you wish.
Fig. 4.2
Wiring for the Neutrik Speakon NL4FC Connector
Wiring for the Neutrik Speakon NL4FC Connector
Fig. 4.3
Stereo Output Wiring
Stereo Output Wiring
If the Mode switch is in the “Bridge” position (for
mono configuration), connect the load across the (+)
terminals of the connector as shown in Figure 4.4.
For Bridge-Mono Mode, non-inverting output, Ch1+
is the positive (+) and Ch2+ is the negative (–).
mono configuration), connect the load across the (+)
terminals of the connector as shown in Figure 4.4.
For Bridge-Mono Mode, non-inverting output, Ch1+
is the positive (+) and Ch2+ is the negative (–).
Fig. 4.4
Bridge-Mono Output Wiring
Bridge-Mono Output Wiring